Manuals / Ricoh / Computer Equipment / Printer

Ricoh VT1730 lbc-&55iih, Adjust the paper delivery rollers to match the paper size, Operation

Models: VT1730

1 63

Download 63 pages 24.03 Kb

Page 19

4.Adjust the paper delivery rollers to match the paper size,

OPERATION

4.Adjust the paper delivery rollers to match the paper size,

D Ifyoupositionthepaperdeliveryrollerson the print area, each roller will make a line on the paper.

Cl You should leave margins of more than 5 mm, 1/5” on the rightand left sides of the paper because the rollers track those areas.

OThe paper delivery rollers may not feed properly and a misfeed may occur if the print contains a large solid fill image.

In such cases, leave margins of approximately 10 mm, 2/5 on both edges and move the rollersfurther away from the edges.

Caution: Do not touch the paper delivery rollers while the machine is operating, or the machine will be damaged.

Preparation For Printhq

lbc-&55iih I

)+ II

I

Image 19

Ricoh VT1730 lbc-&55iih, Adjust the paper delivery rollers to match the paper size, Operation, Preparation For Printhq

Contents

Operating Instructions PRIPORT VT1730Machine Exterior MAJOR COMPONENTS= Keys Operation PanelPage Optimum environmental conditions INSTALLATION REQUIREMENTSMachine Environment Environments To AvoidAccess To The Machine Power ConnectionSupplying The Master Roll Caution When you open or close the topor hands against the switch actuator SUPPLYING THE MASTER ROLL, INK, AND TAPE5. Insert the leading edge of the master roll under the feed roller Supplying The Master Roll 9. Remove the cut-off portion of the master roll10. Close the top cover SUPPLYING THE MASTER ROLL, INK, AND TAPEO Do not remove the seal from the spout of the ink pack Supplying Ink7. Close the ink cover 5. Install a ink pack as shown in the figure6. Press the setting lever green tab B until it clicks 5. Slide in the ink pack holderSUPPLYING THE MASTER ROLL, INK, AND TAPE OptionSupplying Tape For The Tape Dispenser Suppiyl“ngTape For The Tape Dispenser O@ionSupplying Tape For The Tape D~penser Option SUPPLYING THE MASTER ROLL, INK, AND TAPECautions For Printing Paper OPERATION1 mm Cautions When Using The Document FeederOPERATION Preparation For PrintingLoading paper Preparation For Printing4. Place the paper on the paper feed table 3. Move the paper delivery side plates to match the print paper size Setting up the paper delivery table1. Open the paper delivery table 2. Move the paper delivery end plate to match the print paper sizePreparation For Printhq lbc-&55iih4. Adjust the paper delivery rollers to match the paper size OPERATIONStandard Printing 4. Press the Master Making key Standard Printing 7. Remove the prints from the paper delivery tableOPERATION 3. Remove the paper from the paper feed table Restoring The Paper Feed And Paper Delivery Tables1. Turn off the main switch 2. Press down the feed roller pressure lever5. Move the paper delivery end plate to its original position Shifting the image position forward or backward Adjusting The Image PositionShifting the image to the right or left OPERATION 4. Adjust the paper delivery rollers to the print paper positionAdjusting The Image Position P--VAdjusting The Image Density Changing The Printing Speed To Stop The Machine During A Printing Run Making Master And Prints Automatically Making Master And Prints AutomaticallyGroup Printing From The Same Original Class Mode 8. Press the Print Start key 6. Turn on the power Sw tch of the tape dispenser optionGroup Printing From The Same Original Class Mode 5. With the Number keys, enter the desired number of setsGroup Printing From Different Originals Memory Mode 6, Press the Enter key again. The memory returns to Memory 9. Turn on the power switch of the optional tape dispenser~ The Auto Cycle indicator will light Group Printing From Different Originals Memory ModePhoto Mode Printing Thermal Head DAILY MAINTENANCE5. Clean the thermal head as follows 3. Close the ADF cover Contact GlassDAILY MAINTENANCE 1. Open the ADF cover 2. Wipe off the mntact glass with a dry clothdown the feed roller pressure lever Paper Feed RollerDAILY MAINTENANCE 1. Open the paper feed table and pressPaper Delivery Rollers 2. Wipe the exit sensor with a dry cloth Exit SensorDAILY MAINTENANCE 1. Open the paper delivery tableDrum Clamper 1+ +G TROUBLESHOOTINGClose the ADF oover TROUBLESHOOTINGMONITOR WHAT YOU SHOULD DO“ ++ A “ Original When The Misfeed Indicator + Lights3. Close the ADF rover mmpletely When The Misfeed Indicator Lights “ ++ B “ Paper misfeed in paper feed section4. Press the Reset key TROUBLESHOOTINGTo prevent paper misfeeds ~ Curled paper IJ Wrinkled or wavy paper TROUBLESHOOTING “ ++ c “ MaSter misfeed in master feed section3. Reset the master roll. See page 4. Close the top cover 5. Press the Reset keyII ++ E “ Paper wrapping around the drum To prevent paper misfeed When a master misfeed occurs in the master eject section When The Misfeed Indicator Lights When a master misfeed occurs on the drum 1. Open the top cover5. Press the Reset key TROUBLESHOOTING“% + G “ Paper misfeed in the paper exit section When The Open Cover/Unit Indicator Lights When The Open Cover/Unit Indicator ~Lights TROUBLESHOOTINGWhen The Supply/Exchange Indicators Light When Other Indicators Light Poor Printing OPERATION NOTES OPERATION NOTESOperating Cautions CAUTIONSGeneral Cautions 6. Do not operate the machine with any rovers off SPECIFICATIONS SPECIFICATIONS90mmx140 Set up 1050mmx612mmx UOmm 41.3” X 24.1“ X 17.3”