Manuals / Ricoh / Computer Equipment / Printer

Ricoh VT1730 manual Installation Requirements, Machine Environment, Environments To Avoid

Models: VT1730

1 63

Download 63 pages 24.03 Kb

Page 5

INSTALLATION REQUIREMENTS

INSTALLATION REQUIREMENTS

Machine Environment Environments To Avoid

INSTALLATION REQUIREMENTS

Machine Environment

The installation location should be carefully chosen because environmental conditions greatly affect the performance of the machine.

Optimum environmental conditions

Cl Temperature: 10-30 ‘C, 50 -86‘F

Cl Humidity: 20-90 % RH

IJ On a strong and level base (for example, a sturdy desk).

ClThe machine must be level within 5 mm, 1/5” both front to rear and left to right.

Environments To Avoid

D Locations exposed to direct sunlight or strong light (more than 1,500 Iux).

D Locations directly exposed to cool air from an air conditioner or to heat from a heater. (Sudden temperature changes from low to high or vice versa may cause condensation within the machine.)

~ Dusty areas.

Cl Areas with corrosive gases.

Image 5

Ricoh VT1730 manual Installation Requirements, Machine Environment, Environments To Avoid, Optimum environmental conditions

Contents

Operating Instructions PRIPORT VT1730Machine Exterior MAJOR COMPONENTS= Keys Operation PanelPage Machine Environment INSTALLATION REQUIREMENTSEnvironments To Avoid Optimum environmental conditionsAccess To The Machine Power Connectionor hands against the switch actuator Caution When you open or close the topSUPPLYING THE MASTER ROLL, INK, AND TAPE Supplying The Master Roll5. Insert the leading edge of the master roll under the feed roller 10. Close the top cover 9. Remove the cut-off portion of the master rollSUPPLYING THE MASTER ROLL, INK, AND TAPE Supplying The Master RollO Do not remove the seal from the spout of the ink pack Supplying Ink6. Press the setting lever green tab B until it clicks 5. Install a ink pack as shown in the figure5. Slide in the ink pack holder 7. Close the ink coverSupplying Tape For The Tape Dispenser OptionSuppiyl“ngTape For The Tape Dispenser O@ion SUPPLYING THE MASTER ROLL, INK, AND TAPESupplying Tape For The Tape D~penser Option SUPPLYING THE MASTER ROLL, INK, AND TAPECautions For Printing Paper OPERATION1 mm Cautions When Using The Document FeederLoading paper Preparation For PrintingPreparation For Printing OPERATION4. Place the paper on the paper feed table 1. Open the paper delivery table Setting up the paper delivery table2. Move the paper delivery end plate to match the print paper size 3. Move the paper delivery side plates to match the print paper size4. Adjust the paper delivery rollers to match the paper size lbc-&55iihOPERATION Preparation For PrinthqStandard Printing 4. Press the Master Making key OPERATION 7. Remove the prints from the paper delivery tableStandard Printing 1. Turn off the main switch Restoring The Paper Feed And Paper Delivery Tables2. Press down the feed roller pressure lever 3. Remove the paper from the paper feed table5. Move the paper delivery end plate to its original position Shifting the image position forward or backward Adjusting The Image PositionShifting the image to the right or left Adjusting The Image Position 4. Adjust the paper delivery rollers to the print paper positionP--V OPERATIONAdjusting The Image Density Changing The Printing Speed To Stop The Machine During A Printing Run Making Master And Prints Automatically Making Master And Prints AutomaticallyGroup Printing From The Same Original Class Mode Group Printing From The Same Original Class Mode 6. Turn on the power Sw tch of the tape dispenser option5. With the Number keys, enter the desired number of sets 8. Press the Print Start keyGroup Printing From Different Originals Memory Mode ~ The Auto Cycle indicator will light 9. Turn on the power switch of the optional tape dispenserGroup Printing From Different Originals Memory Mode 6, Press the Enter key again. The memory returns to MemoryPhoto Mode Printing Thermal Head DAILY MAINTENANCE5. Clean the thermal head as follows DAILY MAINTENANCE Contact Glass1. Open the ADF cover 2. Wipe off the mntact glass with a dry cloth 3. Close the ADF coverDAILY MAINTENANCE Paper Feed Roller1. Open the paper feed table and press down the feed roller pressure leverPaper Delivery Rollers DAILY MAINTENANCE Exit Sensor1. Open the paper delivery table 2. Wipe the exit sensor with a dry clothDrum Clamper 1+ +G TROUBLESHOOTINGMONITOR TROUBLESHOOTINGWHAT YOU SHOULD DO Close the ADF oover3. Close the ADF rover mmpletely When The Misfeed Indicator + Lights“ ++ A “ Original 4. Press the Reset key “ ++ B “ Paper misfeed in paper feed sectionTROUBLESHOOTING When The Misfeed Indicator LightsTo prevent paper misfeeds ~ Curled paper IJ Wrinkled or wavy paper 3. Reset the master roll. See page 4. Close the top cover “ ++ c “ MaSter misfeed in master feed section5. Press the Reset key TROUBLESHOOTINGII ++ E “ Paper wrapping around the drum To prevent paper misfeed When a master misfeed occurs in the master eject section 5. Press the Reset key When a master misfeed occurs on the drum 1. Open the top coverTROUBLESHOOTING When The Misfeed Indicator Lights“% + G “ Paper misfeed in the paper exit section Lights When The Open Cover/Unit Indicator ~TROUBLESHOOTING When The Open Cover/Unit Indicator LightsWhen The Supply/Exchange Indicators Light When Other Indicators Light Poor Printing OPERATION NOTES OPERATION NOTESGeneral Cautions CAUTIONSOperating Cautions 6. Do not operate the machine with any rovers off 90mmx140 SPECIFICATIONSSPECIFICATIONS Set up 1050mmx612mmx UOmm 41.3” X 24.1“ X 17.3”