Manuals / Roberts Gorden / Household Appliance / Electric Heater

Roberts Gorden TF-160 3 Tube Clamp Package Installation, 4 Coupling and Tube Assembly, Open

Models: TF-380 TF-250 TF-160 TF-200 TF-120 TF-300 TF-350

1 28

Download 28 pages 5.15 Kb

Page 25

Step 7.3 Tube Clamp Package Installation

SECTION 7: HEATER INSTALLATION

Step 7.3 Tube Clamp Package Installation

	Tube Clamp		Bolt
	Flat
	Washer
	Nut
	(Torque 120 in/lb
	13.56	Nm)
Description	Part Number
Tube Clamp Package	01318901
Tube Clamp	01396801
Bolt	97113940
Flat Washer	95211600
Nut	92113900

Step 7.4 Coupling and Tube Assembly

Close coupling	Start Slide bar/Coupling Lock
A with tab.	B onto coupling.

		Tab
			Slide Bar/Coupling Lock
			Wide end
			Coupling
	Open	3" (8 cm) to
		3" (8 cm) to
		4" (10 cm)
	Closed
	C Insert tubes into coupling.	D Tighten coupling to join tubes.
			Slide Bar/Coupling Lock
		Orient coupling so that	Coupling
		Orient coupling so that
		the impact block is in the
		2:00 or 10:00 o’clock
		positions	Tube
		Tube
	Tube	Description	Part Number
	Tube	Coupling	01329600
		Coupling	01329600
		Slide bar/Coupling Lock	01329700
		Tube	91409XXX

19

Image 25

Roberts Gorden TF-160, TF-350, TF-300, TF-120 3 Tube Clamp Package Installation, 4 Coupling and Tube Assembly, Open, Closed

Contents

TF-120 TF-160 TF-200 TF-250 TF-300 TF-350 TF-380 Twin Fire Unitary Infrared HeaterIf you smell gas Quality in Any LanguagePage 2005 TABLE OF CONTENTSPage TABLE OF FIGURES Page 1.1 Manpower Requirements SECTION 1 HEATER SAFETY2.1 Wall Tag SECTION 2 INSTALLER RESPONSIBILITY2.2 Corrosive Chemicals 2.3 National Standards and Applicable Codescentimeters inchesModel FIGURE 4 45 TILT REFLECTOR FIGURE 2: ONE SIDE REFLECTORinches centimetersFIGURE 6 U-TUBE,45 FIGURE 5 U-TUBE,STANDARD REFLECTORFIGURE 7 U-TUBE,OPPOSITE 45 REFLECTOR inchescentimeters A B C D inches A B C DFIGURE 9 LOWER CLEARANCE SHIELD Unapproved4.2 Aircraft Hangars 4.1 Gas Codes4.3 Public Garages 4.4 ElectricalReflector Support Strap & Wire Form Coupling AssemblySECTION 5 MAJOR COMPONENTS FIGURE 11 Major Component DescriptionsTable 1 Contents of Burner Carton 5.1 Standard Parts ListTable 2 Contents of Core and Extension Packages Additional tubing length may be added to heater. Tubing must be heat-treated,aluminized or porcelain coated. Any additional tubing lengths are considered as vent length for length determination. Maximum venting length for minimum heater length is 45 13.7 m, or 22.5 7 m on each tube 6.1 TF-380- 4 Elbow Design Common Vent SECTION 6 SUGGESTED LAYOUTS6.2 TF-350- 4 Elbow Design Common Vent 6.3 TF-300- Double U Design Common VentBurner 90 Elbow10 Typ Tubeon Page 14, Figure SECTION 7 HEATER INSTALLATIONTypical Suspension Details FIGURE 12 Critical Hanger PlacementFIGURE 13 Linear Heater Assembly Overview FIGURE 14 Linear Heater Layout Overview 70 21 m Tube Length Each Side 60 18 m Tube Length Each Side80 24 m Tube Length Each Side Step 7.2 Burner Installation Step 7.1 Burner Tube InstallationStep 7.4 Coupling and Tube Assembly Step 7.3 Tube Clamp Package InstallationOpen ClosedStep 7.4.2 Coupling and Tube Assembly Continued Step 7.4.1 Coupling and Tube Assembly Continued± 2 5 cm Drive Slide Bar until tightStep 7.6 Reflector Installation Step 7.5 Turbulator InstallationThe pictorial drawings of the heater construction in Section 7 are schematic only and provide a general guideline of where hangers, reflector supports and U-clipsare to be installed