Roberts Gorden TF-200, TF-350, TF-300, TF-120, TF-160, TF-250, TF-380 2005, Table Of Contents

TABLE OF CONTENTS

SECTION 1: Heater Safety		1	SECTION 10: Gas Piping		40
1.1 Manpower Requirements		1	SECTION 11: Wiring		41
SECTION 2: Installer Responsibility		2	11.1 Line Voltage Thermostat Wiring		41
2.1	Wall Tag	2	11.2 Low Voltage Thermostat and Relay Wiring		42
2.2	Corrosive Chemicals	2	11.3 Internal Wiring		42
2.3	National Standards and Applicable Codes	2	11.4	Ladder Diagram	43
SECTION 3: Critical Considerations		3	11.5 Electrical Connection to the Burner		43
3.1	Required Clearances to Combustibles	3	SECTION 12: Operation and Maintenance		44
SECTION 4: National Standards and Applicable Codes		7	12.1	Sequence of Operation	44
4.1	Gas Codes	7	12.2	To Shut Off Heater	44
4.2	Aircraft Hangars	7	12.3	To Start Heater	44
4.3	Public Garages	7	12.4	Pre-Season Maintenance and Annual Inspection....	44
4.4	Electrical	7	12.5	Maintenance Checklist	45
4.5	Venting	7	SECTION 13: Troubleshooting		47
4.6	High Altitude	7	13.1	Troubleshooting Flow Chart	47
SECTION 5: Major Components		8	13.2	Manifold Gas Pressure Setting	49
5.1	Standard Parts List	9	SECTION 14: Replacement Parts		50
SECTION 6: Suggested Layouts		11	SECTION 15: General Specifications		52
6.1	TF-380 - 4 Elbow Design (Common Vent)	11	15.1	Material Specification	52
6.2	TF-350 - 4 Elbow Design (Common Vent)	11	15.2	Heater Specifications	52
6.3	TF-300 - Double "U" Design (Common Vent)	11	15.3	Suspension Specifications	52
6.4	TF-160 - Single Elbow Design (Individual Vents)	12	15.4	Controls Specifications	52
6.5	TF-160 Double "L" Design (Individual Vents)	12	SECTION 16: The ROBERTS GORDON® VANTAGE® TF
6.6	TF-250 - Combination "L" and "U" Design		Warranty		53
	(Individual Vents)	12
SECTION 7: Heater Installation		13
7.1	Burner Tube Installation	18
7.2	Burner Installation	18
7.3	Tube Clamp Package Installation	19
7.4	Coupling and Tube Assembly	19
7.5	Turbulator Installation	21
7.6	Reflector Installation	21
SECTION 8: Optional Heater Accessories		23
8.1	U-Tube Configuration	23
8.2	Elbow Package Configuration	26
8.3	Reflector Side Extension	28
8.4	Lower Clearance Shield Installation	29
8.5	Two-Foot Decorative Grille Installation	29
8.6	One-Foot Decorative Grille Installation	31
8.7	Protective Grille Installation	33
SECTION 9: Venting		34
9.1	Venting Requirements	34
9.2	Horizontal Ventilation 4" (10 cm) Pipe	35
9.3	Vertical Ventilation 4" (10 cm) Pipe	35
9.4	Flexible Boot Installation (Single Vent)	36
9.5	Common Sidewall Venting	36
9.6	Vertical Ventilation 6" (15 cm) Pipe	37
9.7	Flexible Boot Installation (Common Vent)	37
9.8	Outside Combustion Air Supply	38

© 2005

All rights reserved. No part of this work covered by the copyrights herein may be reproduced or copied in any form or by any means - graphic, electronic, or mechanical, including photocopying, recording, taping or information storage and retrieval systems - without the written permission of Roberts-Gordon.

Printed in U.S.A.