Manuals / Roberts Gorden / Household Appliance / Electric Heater

Roberts Gorden TF-380, TF-350, TF-300, TF-120 5 Turbulator Installation, 6 Reflector Installation

Models: TF-380 TF-250 TF-160 TF-200 TF-120 TF-300 TF-350

1 28

Download 28 pages 5.15 Kb

Page 27

Step 7.5 Turbulator Installation

SECTION 7: HEATER INSTALLATION

Step 7.5 Turbulator Installation

Turbulator

2.5' Section

TurbulatorTab

Adapter

T

w i s t

Turbulator must be installed in the last standard section of tube.

Turbulator Installation

Model	Tube Section
TF-120	2nd 10’ Section Each side

TF-160	2nd 10’ Section Each side

TF-200	3rd 10’ Section Each side

TF-250	N/A

TF-300	N/A

TF-350	N/A

TF-380	N/A

Description	Part Number
Turbulator Adapter	03051503

Turbulator Section 2.5'	03051504

Tube	91409XXX

	Model	Each Side
	TF-120 & TF-160	1 - 03051503
	TF-120 & TF-160	4 - 03051504
		4 - 03051504

	TF-200	1 - 03051503
	TF-200	2 - 03051504
		2 - 03051504

Pull String

Fold tab around outside

of tube nearest to the vent to hold turbulator in place. Where a vent sleeve

is used, do not fold tab.

Step 7.6 Reflector Installation

NOTE:All tube surfaces must be covered by a reflector, except for a U-Tube.

Burner

Hanger

Burner Tube

Reflector

Description	Part Number
Tube/Reflector Hanger	03090100

Burner Tube	03051XXX

Reflector	02750303

21

Image 27

Roberts Gorden TF-380, TF-350, TF-300, TF-120, TF-200, TF-160, TF-250 5 Turbulator Installation, 6 Reflector Installation

Contents

Quality in Any Language Twin Fire Unitary Infrared HeaterTF-120 TF-160 TF-200 TF-250 TF-300 TF-350 TF-380 If you smell gasPage 2005 TABLE OF CONTENTSPage TABLE OF FIGURES Page 1.1 Manpower Requirements SECTION 1 HEATER SAFETY2.3 National Standards and Applicable Codes SECTION 2 INSTALLER RESPONSIBILITY2.1 Wall Tag 2.2 Corrosive Chemicalsinches centimetersModel centimeters FIGURE 2: ONE SIDE REFLECTORFIGURE 4 45 TILT REFLECTOR inchesinches FIGURE 5 U-TUBE,STANDARD REFLECTORFIGURE 6 U-TUBE,45 FIGURE 7 U-TUBE,OPPOSITE 45 REFLECTORUnapproved inches A B C Dcentimeters A B C D FIGURE 9 LOWER CLEARANCE SHIELD4.4 Electrical 4.1 Gas Codes4.2 Aircraft Hangars 4.3 Public GaragesFIGURE 11 Major Component Descriptions Coupling AssemblyReflector Support Strap & Wire Form SECTION 5 MAJOR COMPONENTS5.1 Standard Parts List Table 1 Contents of Burner CartonTable 2 Contents of Core and Extension Packages Additional tubing length may be added to heater. Tubing must be heat-treated,aluminized or porcelain coated. Any additional tubing lengths are considered as vent length for length determination. Maximum venting length for minimum heater length is 45 13.7 m, or 22.5 7 m on each tube 6.3 TF-300- Double U Design Common Vent SECTION 6 SUGGESTED LAYOUTS6.1 TF-380- 4 Elbow Design Common Vent 6.2 TF-350- 4 Elbow Design Common VentTube 90 ElbowBurner 10 Typon Page 14, Figure SECTION 7 HEATER INSTALLATIONTypical Suspension Details FIGURE 12 Critical Hanger PlacementFIGURE 13 Linear Heater Assembly Overview FIGURE 14 Linear Heater Layout Overview 60 18 m Tube Length Each Side 70 21 m Tube Length Each Side80 24 m Tube Length Each Side Step 7.2 Burner Installation Step 7.1 Burner Tube InstallationClosed Step 7.3 Tube Clamp Package InstallationStep 7.4 Coupling and Tube Assembly OpenDrive Slide Bar until tight Step 7.4.1 Coupling and Tube Assembly ContinuedStep 7.4.2 Coupling and Tube Assembly Continued ± 2 5 cmStep 7.6 Reflector Installation Step 7.5 Turbulator InstallationThe pictorial drawings of the heater construction in Section 7 are schematic only and provide a general guideline of where hangers, reflector supports and U-clipsare to be installed