Manuals / Roberts Gorden / Household Appliance / Gas Heater

Roberts Gorden TF-Series nt Installation, Reflector Joint Detail, Cut away contour with tin snips

Models: TF-Series

1 44

Download 44 pages 59.4 Kb

Page 25

Image 25

ROBERTS GOR DON® TF-SE RIE S SUB MI TT AL SHEE T

nt Installation

Cut away contour with tin snips.

Punch/Drill six 3/32" (2 mm) holes

Reflector Joint Detail

Install Reflector

End Cap

Attach Reflector Joint with six #8 sheet metal screws

Reflector Joint Detail

Reflector

Joint

© 2004 Roberts-GordonAPPLICATION S, ENGI NEERING AND DETAI LED GUID ANCE ON SYSTEMS DESIGN, INSTALLATI ON AND PRODUCT PERFORMANCE IS AVAI LABLE UPON REQUEST. ROBERTS GORDON® PRODUCTS ARE TO BE INSTALLED ONLY IN ACCORDANCE WI TH LOCAL LAWS, CODES AND REGULATIONS, AND ONLY BY A CONTRACTOR QUALI FIED I N THE I NSTALLATION AND SERVICE OF GAS-FIRED HEATING EQUI PMENT.

Page 25

Image 25

Roberts Gorden TF-Series service manual nt Installation, Reflector Joint Detail, Cut away contour with tin snips

Contents

Submittal TF-Series The Twin Fire Unitary Infrared HeaterPage OPTIONAL HEATER ACCESSORIES TABLE OF CONTENTSELBOW PACKAGE CONFIGURATION LOWER CLEARANCE SHIELD INSTALLATIONPage Contents of TF-SeriesBurner Carton STANDARD PARTS LISTContents of Core and Extension Packages DescriptionGENERAL SPECIFICATIONS Material Specification Standard Reflector 45 Tilt Reflector inches Venting on Page 10, Figure TF-SERIESASSEMBLY OVERVIEWTF-SeriesLinear Assembly Overview Typical Suspension Details HEATER INSTALLATION Critical Hanger PlacementTF-120 Coupling Assembly a = 14 36 cmTF-160 TF-160TF-350 TF-300TF-380 TF-350Burner Installation BBurner Tube InstallationCoupling and Tube Assembly Tube Clamp Package InstallationOpen Closedon Page 28, Section , when using ± 2 5 cmdimensions Tighten slide bar as shown belowReflector Installation Turbulator InstallationOption A Option BOption A Option BTF-Series U-TubeAssembly Overview OPTIONAL HEATER ACCESSORIESU-Tube,Standard U-Tube,FullTF-160 TF-120TF-160 TF-200TF-350 TF-Series U-TubeLayout Overviews ContinuedTF-350 TF-380Scribe Reflector Reflector JointFlatten Edge ContourInstall Reflector End Cap nt InstallationReflector Joint Detail Reflector Joint DetailSide Reflector Installation Bracket InstallationREFLECTOR SIDE EXTENSION Shield Support Strap Assembly LOWER CLEARANCE SHIELD INSTALLATIONTWO-FOOTDECORATIVE GRILLE INSTALLATION Grille InstallationReflector Side Extension Installation Frame Shield InstallationReflector Side Extension ROBERTS GORDON TF-SERIE S SU BMI TT AL SHEE TOne-FootDecorative Grille Bracket ONE-FOOTDECORATIVE GRILLE INSTALLATIONIn order to maintain reflector shape, do Decorative Grille90 Elbow End Piece and Reflector End CapReflector End Cap End Piece Insert end piece between grille and bracketsGrille End Cap Grille End Cap InstallationPull outward GrilleVertical Ventilation 4 10 cm Pipe VENTING Horizontal Ventilation 4 10 cm PipeCombustible or Non-CombustibleBoot Clamp Flexible Boot Tube Flexible Boot InstallationTube Combustible orRolled Sleeve Installation for Common Vent Flexible Boot Installation Common VentVertical Ventilation 6 15 cm Pipe RoofVertical Outside Air Supply OUTSIDE COMBUSTION AIR SUPPLYHorizontal Outside Air Supplly Secure with 3 #8 x 3/8 Sheet Metal ScrewsGAS PIPING Line Voltage Thermostat Wiring WIRINGElectrical Shock Hazard This appliance must be connectedElectrical Shock Hazard Low Voltage Thermostat and Relay WiringThis appliance must be connected to a properly grounded electrical source0.2 TF-SeriesLadder Diagram 0.1 TF-SeriesInternal WiringElectrical Cord or Flexible Conduit Burner Blower with DoorScreen and Gasket INTERNAL BURNER DIAGRAMROBERTS GOR DON TF-SERIE S SUB MI TT AL SHEE T WARRANTY IS VOID IF THE ROBERTS GORDON VANTAGE TF LIM- ITED WARRANTYROBERTS-GORDONWILL PAY FOR ROBERTS-GORDONWILL NOT PAY FORROBERTS GOR DON TF-SERIE S SUB MI TT AL SHEE T ROBERTS GORDON TF-SERIE S SU BMI TT AL SHEE T