4

User's Reference

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Top

Submenu

Function

Setting

Default

menu

range

value

 

 

 

 

 

 

 

INK

EMPTY

When replacement of the ink cartridge becomes necessary while

[EMPTY

LATER

CONTROL

MODE

printing is in progress, this setting determines whether printing

MODE]

 

 

 

continues or pauses.

LATER/

 

 

 

This setting is used when the ink cartridge cannot be changed immedi-

PROMPT

 

 

 

ately during printing, such as during unattended operation at night.

 

 

 

 

 

[LATER] causes printing to continue without pause even if ink refilling

[CHANGE

 

 

 

becomes necessary. Printing continues with the small amount of ink

INK SET]

 

 

 

remaining, so the printed image may become faint as the ink runs out.

PIG.

 

 

 

 

In general, it should possible to perform about 1 m2 (10 ft2) of printing

CMYKLcLm/

 

 

 

once this message appears, although the actual varies widely according

PIG.

 

 

 

 

to the amount of ink needed for the particular image. Printing is

CMYKOrGr/

 

 

 

continued only for the data currently being printed. Operation stops

DYE

 

 

 

 

after one image is output.

CMYKLcLm/

 

 

 

[PROMPT] causes operation to pause immediately when the ink

 

 

 

 

 

cartridge needs to be changed. Printing is resumed by replacing the

 

 

 

 

 

cartridge and pressing the [PAUSE] key. Please note, however, that the

 

 

 

 

 

colors of an image in progress may no longer be perfectly matched if

 

 

 

 

 

the unit is allowed to remain paused for two or three hours before

 

 

 

 

 

resuming printing.

 

 

 

 

FILL INK

[FILL INK] : Refills the printing heads with ink. Normally there is no

 

 

 

 

 

need to do this, because refilling is automatic.

 

 

 

 

PUMP UP

[PUMP UP] : Drains ink from the printing heads.

 

 

 

 

 

[HEAD WASH] : This washes the printing heads with optionally

 

 

 

 

HEAD WASH

available cleaning cartridges. For more information, see "3-7 When

 

 

 

 

CHANGE

Moving the Unit... ."

 

 

 

 

INK SET

[CHANGE INK SET] : Performs the [HEAD WASH] and [FILL INK]

 

 

 

 

 

operations.

 

 

 

 

 

This is used when switching the ink type. Before running this, choose

 

 

 

 

 

the type of ink to be used after the change.

 

 

 

 

 

For more information, see "3-4 Changing the Type of Ink."

 

 

 

 

 

 

 

 

BIDIRECTION

 

This adjusts for slippage when performing bidirectional printing.

-20 to +20

Correction

 

 

This must be readjusted when you have replaced the material with a

(In steps of 1)

value when

 

 

different type or adjusted the head height.

 

 

shipped

 

TEST PRINT

[TEST PRINT]: This menu is for verifying the adjustment.

 

 

from the

 

ADJUST

[ADJUST]: This sets the correction value.

 

 

factory

 

 

For more information, see "2-6 Performing Printing -- Making

 

 

 

 

 

Corrections for Printing -- Bidirectional Correction."

 

 

 

 

 

 

 

 

 

CARIBRATION

 

This corrects for errors in the amount of feed of the grit rollers due the

-2.0%

to

0%

 

 

type of material.

+2.0%

 

 

 

Be sure to make this setting when you have replaced the material with

(In steps of

 

 

 

a different type.

0.05%)

 

 

 

Make this setting again when horizontal stripes are plainly visible on

 

 

 

 

 

printing results.

 

 

 

 

TEST PRINT

[TEST PRINT]: This menu is for verifying the adjustment.

 

 

 

 

ADJUST

[ADJUST]: This sets the correction value.

 

 

 

 

 

For more information, see "2-6 Performing Printing -- Making

 

 

 

 

 

Corrections for Printing -- Feed Correction."

 

 

 

 

 

 

 

 

OVER

—

You can carry out the same printing superimposed over the same

NONE/2/3

NONE

PRINT

 

location. When printing materials such as fabric, colors may not come

 

 

 

 

 

out well with just a single printing pass.

 

 

 

 

 

This should normally be set to [NONE].

 

 

 

 

 

For more information, see "2-9 Other Functions -- Performing Over-

 

 

 

 

 

printing."

 

 

 

 

 

 

 

 

SLEEP

—

This sets the time that elapses before the unit enters the SLEEP mode.

NONE/15

15 min

 

 

The SLEEP mode is enabled when the FJ-50/40 has been inactive for a

min to

 

 

 

specified time. (When in the SLEEP mode, the POWER LED flashes

120 min

 

 

 

once per second.)

(In steps of

 

 

 

To release the SLEEP mode...

15 min)

 

 

 

- Touch any key on the control panel. - Send data from the computer.

 

 

 

 

 

- Open the front cover. - Move the sheet loading lever toward the back of the unit.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

53