Chapter 2. Using Effects

*1: For effect types 43–45, you can hold down [FUNC] and press [F2] (SUB) to access a sub-parameter screen. The tables shown below list the parameters that appear in these screens. Press [F3] (EXIT) to return to the previous screen.

43 SUBSONIC

Value

Explanation

 

 

 

E.LEVEL

0–127

Adjusts the volume of the effect sound.

PITCH

0–127

Adjusts the frequency of the sine wave.

ATTACK

0–127

Adjusts the time from when the source exceeds the threshold until the sine wave is heard.

44 OSCILLATOR(PAD)

Value

Explanation

 

 

 

EFFECT LEVEL

0–127

Adjusts the volume of the effect sound.

PAD1 KEY

C- –G9

Adjusts the key sounded by the oscillator when you press PAD 1.

LFO RATE

0–127

An LFO is an oscillator used to apply modulation; by increasing the vibrato or PWM you

 

 

can modulate the pitch or tone in a variety of ways.

LFO WAVE

SAW,

TRI

 

TRI,

(Triangle wave)

 

SQR,

SQR

 

S-H

(Square wave)

 

 

 

 

SAW

 

 

(Sawtooth wave)

 

 

S-H

 

 

(Sample & Hold wave)

 

 

 

OSC TUNE

-24–+24

Specifies the coarse tuning (semitone steps) of the oscillator pitch.

OSC VIB DEPTH

0–127

Adjusts the depth of vibrato (using the LFO to cyclically modulate the pitch) for the oscil-

 

 

lator.

OSC XMOD

0–127

Adjusts the depth of cross modulation (using the SUB OSC to modulate the pitch of the

 

 

oscillator).

OSC LEVEL

0–127

Adjusts the volume of OSC.

SUB OSC WAVE

SAW,

Selects the SUB OSC waveform. (The choices are the same as for OSC WAVE on p. 39)

 

TRI,

 

 

PLS1–9

 

SUB OSC TUNE

-24–+24

Adjusts the coarse tuning (semitone steps) of the SUB OSC pitch.

SUB OSC VIB DEPT

0–127

Adjusts the depth of vibrato (using the LFO to cyclically modulate the pitch) for the SUB

 

 

OSC.

SUB OSC LEVEL

0–127

Adjusts the SUB OSC volume.

RING SRC1

OSC,

Selects the two inputs for the ring modulator.

RING SRC2

SUB

(MFX IN: MFX input source)

 

OSC,

 

 

NOISE,

 

 

MFX IN

 

RING LEVEL

0–127

Adjusts the volume of the ring modulator.

NOISE LEVEL

0–127

Adjusts the volume of the noise generator.

PORTA TIME

0–100

Adjusts the time over which pitch change will occur for the portamento effect (which cre-

 

 

ates smooth transitions between pitches).

45 ENVELOPER(PAD)

Value

Explanation

 

 

 

ATTACK

0–127

Adjusts the time from when you release the pad until the volume falls to the minimum.

FILTER TYPE

LP (-12),

Low pass filter with a -12 dB slope

 

BP (-12),

Band pass filter with a -12 dB slope

 

HP (-12),

High pass filter with a -12 dB slope

 

LP (-24),

Low pass filter with a -24 dB slope

 

BP (-24),

Band pass filter with a -24 dB slope

 

HP (-24)

High pass filter with a -24dB slope

*2: Available note values for synchronization (In the case of delay time, the result cannot exceed approximately three seconds.)

32nd note( ), 16th note( ), 8th note triplet( ), dotted 16th note( ), 8th note( ), quarter note triplet( ), dotted

8th note( ), quarter note( ), half note triplet( ), dotted quarter note( ), half note( ), dotted half note( ), whole note( )

40