Roland TD-20 About Expansion Board

86

About Expansion Board

Expansion boards (optional) are cards that allow you to

upgrade the system and add new instruments and drum kits.

The bottom panel of the TD-20 has a slot that allows

expansion boards to be installed.

Install only the specified circuit board (SOUND & SYSTEM

EXPANSION BOARD for TD-20).

* Sound expansion boards for the Roland JV/XP/XV/Fantom

series cannot be used.

901

• To avoid the risk of damage to internal components that

can be caused by static electricity, please carefully observe

the following whenever you handle the board.

1

• Before you touch the board, always first grasp a metal

object (such as a water pipe), so you are sure that any

static electricity you might have been carrying has been

discharged.

2

• When handling the board, grasp it only by its edges.

Avoid touching any of the electronic components or

connectors.

5

• Save the bag in which the board was originally

shipped, and put the board back into it whenever you

need to store or transport it.

911

• Do not touch any of the printed circuit pathways or

connection terminals.

912

• Never use excessive force when installing a circuit board. If

it doesn’t fit properly on the first attempt, remove the

board and try again.

913

• When circuit board installation is complete, double-check

your work.

914

• Always turn the unit off and unplug the power cord before

attempting installation of the circuit board (SOUND &

SYSTEM EXPANSION BOARD for TD-20).

915

• Install only the specified circuit board (SOUND & SYSTEM

EXPANSION BOARD for TD-20). Remove only the

specified screws.

1.

Always turn the TD-20 off and unplug the power

cord before attempting installation of the circuit

board (SOUND & SYSTEM EXPANSION BOARD

for TD-20).

2.

Remove only the eight screws as indicated

below, and open the cover located on the

bottom of the TD-20.

fig.00-049ae

3.

Check that the plastic board holders are

positioned as shown figure. Rotate them if

necessary.

fig.00-049be

Cautions When Installing a

Expansion Board

How to Install a Expansion

Board

Removal screws

Board holder

Connector

Expansion board

TD-20_Ref_e.book 86 ページ２００５年５月２５日　水曜日　午前９時４９分

Contents

Main As of January 15, 2005 (ROLAND) 03453923 05-6-5N Owners Manual To resize thickness, move all items on the front cover and registration marks to left or right. Apparatus containing Lithium batteries IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Page Page IMPORTANT NOTES Memory Backup Repairs and Data Maintenance Additional Precautions Before Using Cards Contents Chapter 5. Trigger Settings [TRIGGER].................................................44 Chapter 4. Effect Settings.......................................................................38 Chapter 3. Mixer Settings .......................................................................37 Chapter 2. Drum Instrument Settings [INST] ........................................31 Chapter 7. Sequencer (Recording/Editing) ...........................................61 Chapter 6. Sequencer (Playback)...........................................................51 Page Features An Easy User Interface Everything Is New! Module StandV-Hi-HatPads 560 New Drum Sounds Expanded V-Editing Top Quality Signal Processing Functions For Stage Sequencer Advanced Tempo Functions Expansion Board MIDI Sound Module Potentials V-LINK function Panel Descriptions Top Panel Page Rear Panel 12 8 93 4 5 7 11106 Front Panel Setting Up the Kit Mounting the TD-20 on the Stand Set Up Example Connecting the Pads and Pedals Connecting Headphones, Audio Equipment, Amps, or Other Gear Turning Off the Power Turning On/Off the Power Precautions When Turning on the Power Connecting the Hi-Hat (VH-12) and Setting the VH Offset Adjusting the Offset Adjusting Mesh Head Tension (PD-125/105) 13 42 5 6 Listening to the Demo Song Demo Song Button Operation and Displays Changing Data Values Cursor Function Buttons ([F1][F5]) Group Faders Choosing Pads from the TD- 20s Top Panel Button Operation and Displays How to Play Patterns How to Turn the Metronome (Click) On/Off How to Adjust the Tempo About the Preset Drum Kits Adjusting the Display Contrast About the Display in the Upper Right of the Screen Playing Methods Change the Nuance of the Rim Shot Pad (PD-125/105) Edge Shot Cymbal (CY-15R/14C) Positional Sensing Choke Play Chapter 1. Drum Kit Settings [KIT] Choosing a Drum Kit About the DRUM KIT Screen Kit Parameters [F2 (FUNC)] Output Level Monitor [F5 (MONITOR)] Playing Brushes [F3 (BRUSH)] Adjusting the Volume [F1 (VOLUME)] Naming a Drum Kit [F3 (NAME)] Playing Cross Stick [F5 (XSTICK)] Chapter 2. Drum Instrument Settings [INST] Choosing a Pad to Edit Choose by Hitting a Pad Selecting an Instrument from the List [F1 (LIST)] About the Display at the Lower of the Instrument Name Editing Drum Sounds [F2 (EDIT)] Editing an Acoustic Drum Kit (V-EDIT) KICK HI-HAT SNARE TOM CRASH/SPLASH/CHINA/RIDE Other Instruments Use [+/-] or [VALUE] to adjust settings. Strike a pad. Press [INST] - [F3 (CONTROL)]. Using Pads/Pedal as Controllers [F3 (CONTROL)] Playing a Pattern by Hitting a Pad (Pad Pattern) [F1 (PATTERN)] Changing the Pitch with the Hi-Hat Pedal [F2 (PDLBEND)] When Setting Multiple Pads to the Same Note Number MIDI Settings for Each Pad [F3 (MIDI)] MIDI Note Numbers transmitted by Hi-Hat [F4 (HH MIDI)] MIDI Note Number transmitted by Brush Sweep/Cross Stick [F5 (BR MIDI)] About the Gate Time Chapter 3. Mixer Settings Using Group Faders to Edit (MIX EDIT) Mixer Parameters [MIXER] Chapter 4. Effect Settings Effects On and Off Switches [EFFECTS SWITCH] Using the Compressor and EQ [COMP/EQ] Compressor (COMP) Equalizer (EQ) Ambience [AMBIENCE] Multi-Effects [MULTI EFFECTS] REVERB BEAT DELAY Multi-Effects Parameters FLANGER DISTORTION OVERDRIVE ENHANCER PITCH SHIFT Press [F1] to turn the master effects on. Press [MASTER COMP/EQ]. Master Effects [MASTER COMP/EQ] Chapter 5. Trigger Settings [TRIGGER] Use [+/-] or [VALUE] to select the trigger type. 6. Use [+/-] or [VALUE] to select the Trigger Bank. Setting the Pad Sensitivity [F2 (BASIC)] Pad Sensitivity Minimum level for the pad (Threshold) Hi-Hat Settings [F3 (HI-HAT)] Adjusting the Offset of VH-11 Adjusting the Offset of VH-12 Automatically Eliminate Crosstalk Between Pads [F4 (XTALK)] Press [TRIGGER] - [F5 (ADVANCE)]. Advanced Trigger Parameters [F5 (ADVANCE)] Trigger Signal Detection Time (Scan Time) Detecting Trigger Signal Attenuation (Retrigger Cancel) Volume Levels Time Double Triggering Prevention (Mask Time) Rim/Edge Dynamic Response (Rim Gain) Rim Shots Response (Rim Shot Adjust) Cross Stick Threshold (XStick Thrshld) Striking force Cross Stick Threshold (0127) Playing Bow, Bell, and Edge (3-Way Triggering) Naming a Trigger Bank [F5 (Name)] Chapter 6. Sequencer (Playback) Basic Operation Using Preset Patterns User Patterns (Pattern U 101200) Choosing a Pattern [PATTERN] About the PATTERN screen. Select a Pattern from the List [F1 (LIST)] Playing Back a Pattern [PLAY] Tempo Adjustment Setting the Tempo by Hitting a Pad (Tap Tempo) Synchronizing with an External MIDI Device Part Settings [F2 (PART)] Muting a Specific Part [F1 (MUTE)] Make Settings for the Backing Part [F2 (BACKING)] Choosing a Percussion Set Percussion Set Settings Master Tuning Selecting a Percussion Instrument Instrument Numbers/Instrument Names Variation Tones Percussion Part Settings [F3 (PERC)] Selecting a Percussion Instrument from the List [F1 (LIST)] Naming a Percussion Set [F3 (NAME)] Making the Settings for Each Percussion Instrument [F2 (EDIT)] Volume/Pan Settings for Each Part [F4 (MIXER)] Effect Settings for Backing Parts [F5 (REV/CHO)] About Play Type (LOOP, ONESHOT, TAP, VLINK) Pattern Settings [F3 (FUNC)] Time Signature/Number of Measures/Tempo Settings [F1 (SETUP)] Choosing a Playback Method [F2 (TYPE)] Starting and Stopping the Metronome (Click) On/Off Using a Indicator as a Click Chapter 6. Sequencer (Playback) Press [CURSOR] to select the parameter. Setting the Click Chapter 7. Sequencer (Recording/Editing) How to Record Recording a Pattern [REC] Press [F5 (NEW)]. Press [CURSOR] to select the parameter. (4) Part Setting (2) Set the Time Signature, the Number of Measures, and the Tempo (5) Set the Recording Method Rec Mode Quantize Checking the Tones and Phrases During Recording (Rehearsal) Editing a Pattern [F4 (EDIT)] Copying a Pattern [F1 (COPY)] Connecting Two Patterns [F2 (APPEND)] Erasing a pattern [F3 (ERASE)] Deleting a Pattern [F4 (DELETE)] Save/Load and Copy Functions of the TD- 20 Saving a Pattern to a Memory Card [F1 (SAVE)] Saving Patterns to a Memory Card [F5 (CARD)] Loading a Pattern from a Memory Card [F2 (LOAD)] Deleting a Pattern from a Memory Card [F3 (DELETE)] Chapter 8. Copy Function [COPY] Chapter 9. Using a CompactFlash Memory Card [CARD] Save/Load and Copy Functions of the TD- 20 Saving Data to a Memory Card [F1 (SAVE)] Loading Data from a Memory Card [F2 (LOAD)] Deleting Data from a Memory Card [F3 (DELETE)] Formatting a Memory Card [F4 (FORMAT)] Checking the State of a Memory Card [F5 (INFO)] Chapter 10. Settings for the Entire TD-20 [SETUP] TD-20 Soft Thru MIDI OUT MIDI IN Device ID: 16 Local Control Device ID Device ID: 17 MIDI IN Transmit data Device ID: 17 System Exclusive is not received HH Note# Border (Hi-Hat Note Number Border) Turning the Reception/Transmission of Program Changes On/Off MIDI Messages for Detailed Performance Expressions [F3 (CTRL)] Saving Data Loading Data to the TD-20 Saving Data to an external MIDI Device (Bulk Dump) [F5 (BULK)] Selecting Output Destinations [F2 (OUTPUT)] Output Destination for the Drum Output Destination for the Sequencer Parts/Metronome Click/Sound Input from MIX IN [F4 (OTHER)] Setting the Switches [F3 (CONTROL)] Using Foot Switches [F1 (FOOT SW)] Using Pads as Switches [F2 (PAD SW)] Other Settings [F4 (OPTION)] Preview Button Settings [F1 (PREVIEW)] Restoring the Factory Settings [F5 (F RESET)] Chapter 11. Drum Kit Chain [CHAIN] Creating a Drum Kit Chain Naming a Drum Kit Chain [F5 (NAME)] Playing with a Drum Kit Chain Chapter 12. Other Functions [TOOLS] Output Level Monitor [F1 (MONITOR)] Checking the Current Status [F2 (INFO)] Press [TOOLS]. Turning V-LINK On/Off Using V-LINK V-LINK Functions that the TD-20 Can Control and MIDI Messages About Expansion Board Cautions When Installing a Expansion Board How to Install a Expansion Board Page propos des carte dextension Prcautions prendre lors de linstallation dune carte dextension Installation dune carte dextension (French language for Canadian Standard) Page Messages and Error Messages Error Messages Messages and Error Messages Messages Drum Instrument List KICK KICK PROCESSED KICK ELEC TOM TOM ELEC HI-HAT CRASH SPLASH RIDE CHINA PERCUSSION PERC ANALOG SFX About Remarks About Snare/Tom About Cymbal Copyright Note Number (Factory Settings) Drum Kit 1. Latin Toys Percussion Set Note Number (Factory Settings) Percussion Set Settings Backing Instrument List GUITAR ORGAN CHROMATIC PERCUSSION SYN. BRASS SYN. PAD SYN. LEAD PIPE SYN. SFX ETHNIC MISC PERCUSSIVE GUITAR BASS FX MIDI Implementation Chart PERCUSSION SOUND MODULE Model TD-20 Date : Jan. 25, 2004 Version : 1.00 MIDI Implementation Chart Specifications TD-20: Percussion Sound Module Page CLICK ([SHIFT] + [TEMPO]) Drums Backing Part Click TD-20 Block Diagram KICK SNARE HI-HAT (AUX) Kit Volume TOMS MASTER DIRECT 1 DIGITAL OUT DIRECT 4 MIX IN DIRECT 2 Index E D C F O N M P S Q R T X V U Preset Drum Kit List Preset Pattern List Apparatus containing Lithium batteries ADVARSEL! IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS As of January 15, 2005 (ROLAND) 03453923 05-6-5N Information Owners Manual To resize thickness, move all items on the front cover and registration marks to left or right.