Runco CW-50MC manual RS-232C Commands, How to read this table

RS-232C Commands

How to read this table:

• RS-232C Adjustment Validity: Indicates whether or not the RS-232 adjustment mode can be used.

• Normal Validity:	Indicates whether or not the normal-operation mode can be used
• Numerical Direct Validity:	When a number (3-digit number) is attached to the end of a command, the command can
	directly set that adjustment value.

○ or ●: Valid		No Mark: Invalid				NOTE: ● = values not stored in the last memory
	Name	Full Name	Adjustment	Validity	Direct		Description
	Command		RS-232C	Normal	Numerical
			Validity		Validity
A	AJN	-	●				Terminates the RS-232C installer adjustment mode.
	AJY	ADJUST: ON		●			Starts the RS-232C installer adjustment mode.
	AMN	AUDIO MUTING: OFF	●	●			Turns audio mute OFF.
	AMY	AUDIO MUTING: ON	●	●			Turns audio mute ON.
	AST	AUTO SET UP MODE		○			Executes AUTO SETUP.
B	BHI	B GAIN	○		○		Adjusts BLUE GAIN HIGH-LIGHT.
	BLW	B OFFSET	○		○		Adjusts BLUE OFFSET LOW-LIGHT.
	BRA	BAUD RATE: #####-232C	●				Displays the current baud rate.
	BRAS01	BAUD RATE: 1200-232C	○				Sets the UART setting to 232C (1200bps).
	BRAS02	BAUD RATE: 2400-232C	○				Sets the UART setting to 232C (2400bps).
	BRAS03	BAUD RATE: 4800-232C	○				Sets the UART setting to 232C (4800bps).
	BRAS04	BAUD RATE: 9600-232C	○				Sets the UART setting to 232C (9600bps).
	BRAS05	BAUD RATE: 19200-232C	○				Sets the UART setting to 232C (19200bps).
	BRAS06	BAUD RATE: 38400-232C	○				Sets the UART setting to 232C (38400bps).
	BRT	BRIGHTNESS: ***	○		○		Adjusts brightness.
	BSL	B SIDEBAR ADJ. LEVEL	○		○		Adjusts BLUE SIDEBAR ADJUST LEVEL.
C	CFR	FREQ. ADJ.: ***	○		○		Adjusts the clock frequency (PLL frequency).
	CGB	C. DETAIL BLUE: ***	○		○		Adjusts color detail BLUE.
	CGC	C. DETAIL CYAN: ***	○		○		Adjusts color detail CYAN.
	CGG	C. DETAIL GREEN: ***	○		○		Adjusts color detail GREEN.
	CGM	C. DETAIL MAGENTA: ***	○		○		Adjusts color detail MAGENTA.
	CGR	C. DETAIL RED: ***	○		○		Adjusts color detail RED.
	CGY	C. DETAIL YELLOW: ***	○		○		Adjusts color detail YELLOW.
	CLS	COLOR SYSTEM: #####	●				Displays the current color system.
	CLSS01	COLOR SYSTEM: AUTO	○				Sets the color system to AUTO.
	CLSS02	COLOR SYSTEM: NTSC	○				Sets the color system to NTSC.
	CLSS03	COLOR SYSTEM: PAL	○				Sets the color system to PAL.
	CLSS04	COLOR SYSTEM: SECAM	○				Sets the color system to SECAM.
	CLSS05	COLOR SYSTEM: 4.43NTSC	○				Sets the color system to 4.43NTSC.
	CLSS06	COLOR SYSTEM: PAL M	○				Sets the color system to PAL M.
	CLSS07	COLOR SYSTEM: PAL N	○				Sets the color system to PAL N.
	CM1	NORMAL	○	○			Sets the Normal color mode.
	CM2	ISF	○	○			Sets the ISF color mode (retake).
	CNT	CONTRAST: ***	○		○		Adjusts contrast.
	COF	COLOR OFF: ********	●				Displays the current COLOR OFF setting.
	COFS00	COLOR OFF: DISABLE	○				Disables COLOR OFF.
	COFS01	COLOR OFF: ENABLE	○				Enables COLOR OFF.
	COL	COLOR: ***	○		○
	CPH	PHASE ADJ.: ***	○		○		Adjusts the phase (PLL phase).

22