GET Commands
What are GET Commands?
•They are commands for outputting TXD such as adjustment data from the internal microcomputer of the plasma display to a PC.
•Adjustment data, etc., is output in ASCII code.
NOTE: Command names are given inside brackets < >.
•Data output format
STX (o2hex)
Data
Data
....
Checksum
ETX (03hex)
NOTE:
1)GET commands will be invalid when no ID NO. Set is assigned to the set.
2)GET commands will be invalid when wildcard (*) is used in the ID No. Set when sending the command.
1) <GST> (GET STATUS)
Order | Data Contents |
| Size |
|
|
| Remarks |
|
|
1 | Display data |
| 3byte | See below |
|
|
|
| |
2 | Power data |
| 3byte | See below (The third character is sub input) |
|
| |||
3 | Input function data (main) |
| 3byte | Input data when GST is received (INPUT1 to 5 is displayed as IN1 to 5) | |||||
4 | Input function data (sub) |
| 3byte | Sub input data when GST is received Note 3 |
|
| |||
|
|
|
| (INPUT1 to 5 is displayed as IN1 to 5) |
|
| |||
5 | Screen size data |
| 1byte | See below |
|
|
|
| |
6 |
| 1byte | 0: OFF (1 screen) | 1: | 2: PinP (lower right) | ||||
|
|
|
| 3: PinP (upper right) | 4: PinP (upper left) | 5: PinP (lower left) | |||
|
|
|
| 6: PoutP |
|
|
|
| |
7 | FUNCTIONAL LOCK data |
| 1byte | 0: LOCK OFF | 1: BUTTONS LOCK | 2: IR LOCK | |||
|
|
|
| 3: IR & BUTTONS LOCK | 4: MEMORY LOCK | ||||
8 | Dummy Data |
| 3byte |
|
|
|
| ||
9 | Temperature data 2 |
| 3byte | (Internal temperature: Reference value) oC Note 1 | |||||
10 | Temperature data 3 |
| 3byte | (Internal temperature: Reference value) oC Note 1 | |||||
11 | Serial |
| 15byte |
|
|
|
|
|
|
12 | Dummy data |
| 3byte |
|
|
|
| ||
13 | Dummy data |
| 3byte |
|
|
|
|
|
|
14 | HOURMETER |
| 5byte | Display the time. |
|
|
|
| |
15 | Checksum |
| 2byte |
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| Display data | First character |
| Generation data: 4 (fixed) |
|
| |||
|
| Second character | Inch data: 4 (43 inches), 5 (50 inch) |
|
| ||||
|
|
|
|
|
|
| |||
|
| Third character |
| Destination data: M (fixed) |
|
| |||
| Power Data | First character |
| Power state & signal state |
|
| |||
|
|
|
|
| PN (POWER ON & normal signal input) |
|
| ||
|
|
|
|
| PL (POWER ON & no input) |
|
| ||
|
| Second character | PO (POWER ON & OUT OF RANGE signal input) |
| |||||
|
| SN (Normal standby) |
|
|
| ||||
|
|
|
|
|
|
|
| ||
|
|
|
|
| SW (Standby by AUTO POWER OFF) |
|
| ||
|
|
|
|
| SS (Standby by SD or PD) |
|
| ||
|
|
|
|
| Sub input signal state during |
| |||
|
| Third character |
| N (Normal signal input) | L (No input) |
|
| ||
|
|
|
|
| O (OUT OF RANGE signal input) |
|
| ||
| Screen size data | First character |
| (0) Pix by Pix or Letterbox, (1) STD (4:3), (2) ANAMPHC 16:9, (3) Letterbox |
| ||||
|
| (1080i), (4) Cinema, (5) Virtualwide, (8) Letterbox (1035i), (9) Underscan |
| ||||||
|
|
|
|
|
| ||||
NOTE 1) During standby and immediately after POWER ON, the proper value is not output. In this case, wait a moment after POWER ON, then get the data. The temperature data is output as a reference (the values are not guaranteed values). Normally, refer to temperature data 3.
NOTE 2) During standby and during
NOTE 3) During standby and during
28
