Service/Setup Menu, Video NR Noise, Reduction | Runco SP-60DHD

PlasmaWall Service Remote Control

For the vast majority of installations, the DHD Controller remote control gives you all the control you need over display quality settings. However, there are two settings internal to the PlasmaWall that can improve the displayed image quality on INPUT 1: VIDEO NR (noise reduction) and MPEG FILTER. These settings can be found in the Setup Menu, shown in Figure A-2.

PLASMAWALL		INPUT 1
PICTURE SCREEN		SET-UP OPTION
	COLOR TEMP.	: MIDDLE
	AUTO OFF	: OFF
	VIDEO NR	: MIDDLE
	MPEG FILTER	: LOW
	CHROMA EE	: ON
	FILM MODE	: OFF
	COLOR SPACE	: RGB
	SIGNAL	: 720p
SET SET		MENU EXIT

A.2

Service/Setup Menu

Figure A-2. PlasmaWall Setup Menu
To apply Digital Noise Reduction (DNR) to the input signal, select Video NR from the	Video NR (Noise
Set-Up menu. Noise reduction is useful for improving the signal-to-noise ratio of video	Reduction)
signals.
To change the Noise Reduction setting on INPUT 1:

1.Press 1 to switch to PlasmaWall INPUT 1.

2.Press MENU on the PlasmaWall Service Remote Control.

3.Press or to select SETUP.

4.Press to select VIDEO NR, then press SET.

5.Press or to select the desired amount of noise reduction (OFF, LOW, MIDDLE or HIGH).

6.Press SET to confirm your selection.

PlasmaWall SP Series Owner’s Operating Manual

A-3

Image 79

Runco SP-60DHD, SP-42DHD, SP-50DHD manual Service/Setup Menu, Video NR Noise, Reduction

Contents

SP-42DHD SP-50DHD SP-60DHD Page For Plasma Displays Three Year Limited Warranty RIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and TroubleshootingSpecifications Appendix A. PlasmaWall Service Remote Control List of Figures List of Figures About This Manual Introduction If you need Turn to Using This Manual Key Features and Benefits Description, Features and Benefits Optional Accessories Controls and Functions Controls and IndicatorsPlasmaWall at a Glance PlasmaWall Model SP-42DHD Rear Panel PlasmaWall Model SP-50DHD Rear Panel PlasmaWall Model SP-60DHD Rear Panel External Speaker Output Left Main Power SwitchDigital RGB Input 2 DVI-D External Speaker Output Right IR Sensor Power ButtonDHD Controller Front Panel Runco Icon Down Button UP ButtonLeft Button Enter Button Inputs 3. DVI 1 / DVI 2 Digital Component Video RCA connectorsDHD Controller Rear Panel DVI OUT RS-232 Control Port Composite Video InputMain AC Fuse DHD Controller Remote Control DHD Controller Remote Control Menu IR Output IndicatorEnter Light ISF DAY CinemaSVC ISF Night Remote Control Installation Other surfaces Step Procedure For Details, refer to Quick Setup Mounting the PlasmaWall InstallationConsiderations High-Altitude Operation Ventilation Ambient Light Installation Connections to the PlasmaWall and DHD Controller Connecting PlasmaWall to the DHD Controller RS-232 Connection from the DHD Controller to the PlasmaWall DVI Source DVD Player or HD Tuner with Hdmi or DVI out Connecting SourceComponents to the DHD DVI Connections See Figure Digital DTV RGB Connections Digital DTV RGB Connections See Analog Computer RGB Connections See Figure Refer to Computer/Video Signal Compatibility on page 64 forPersonal Computer DVD Player, VCR Satellite Receiver Laser Disc etc Composite/S-Video/Component Video Connections See Figure RS-232 Controller Connecting 12-Volt Trigger Outputs to External EquipmentConnection 11. Installing the Cable Ties Operation Turning on the Power You must enter a passcode to access the Service menu Operation Using the On-Screen Menus Aspect Ratio ISF PresetsService Input Source HD Pass Thru 1 HD Pass Thru Main MenuInput Source Aspect Ratio Remote Aspect Ratio Control Description Key Aspect Ratio Settings Picture Brightness Contrast Color Tint Sharpness Picture Typical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Left/Right Up/Down Width Height Overscan Input Position Serial Number Hardware Firmware 0002.034B Date Nov 25 ISF PresetsISF Presets ISF Night ISF Day Custom Save Factory Default Information Calibration Gain/Offset Refer to ISF Night Display Color, above Should be used by ISF-certified technicians only Service Input Names Restore Composite Video Component SD HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Operation Cleaning the Screen Maintenance and TroubleshootingCleaning Cleaning the Display Panel Body and Remote Control Symptom Possible Causes Solution Troubleshooting Tips Computer/Video Signal Maintenance and Troubleshooting Letterbox Enter Serial Communications Aspect Ratio Commands CommandValue Description Min/max Stored? Power On/Off Commands Input Selection Commands Image Preset Commands Output Shift Commands Value Description Min/max Stored? Input Position Commands Bkgnd Enter key Command Parameter min/max Value Stored? Description Model SP-50DHD SpecificationsPlasmaWall Specifications Model SP-42DHD DHD Controller Specifications PlasmaWall Dimensions 14.8 34.3 49.1 M8 Screw KHz Computer/Video Signal CompatibilityInput Refresh Rate Resolution Remarks Horiz 56.0 45.1 Specifications Overview Figure A-1. PlasmaWall Service Remote Control DVI-D RGB SetupAspect Ratio RGB-HD Video NR Noise Service/Setup MenuReduction PlasmaWall Service Remote Control Page Runco CL-810 Owner’s Operating Manual