Error Codes

GB

 

 

 

 

 

 

 

 

Error Items

Code

Error Beep

 

Cause/Remedy

 

 

 

 

 

 

 

 

 

 

 

 

Cause:

Power frequency is other than 50 Hz.

 

 

 

 

 

Remedy: • Unplug the power cord plug and check if the

 

 

 

 

one beep

 

power frequency is 50 Hz.

 

 

Power frequency Error(50/60Hz)

E1

 

• Plug the power cord in 50 Hz power source and

 

 

for 2 sec

 

 

 

 

 

 

see If “E1” appears. If the error code is displayed

 

 

 

 

 

 

 

 

 

 

 

 

again even after the correct power source is

 

 

 

 

 

 

provided, contact the nearest service centre.

 

 

 

 

 

 

 

 

 

 

 

 

Cause:

Thermistor Sensor which is supposed to sense

 

 

 

 

one beep

 

the temperature of the cavity inside does not

 

 

Thermistor Open Error

E21

 

work properly. (Thermistor Sensor open)

 

 

for 2 sec

Remedy:

Unplug the power cord and wait for more than 10

 

 

 

 

 

 

 

 

 

 

seconds. Plug the power cord again. If the symptom

 

 

 

 

 

 

persists, contact the nearest service centre.

 

 

 

 

 

 

 

 

 

 

 

 

Cause:

Thermistor Sensor which is supposed to sense

 

 

 

 

 

 

the temperature of the cavity inside does not

 

 

Thermistor Short Error

E22

one beep

 

work properly. (Thermistor Sensor short)

 

 

for 2 sec

Remedy:

Unplug the power cord and wait for more than 10

 

 

 

 

 

 

 

 

 

 

seconds. Plug the power cord again. If the symptom

 

 

 

 

 

 

persists, contact the nearest service centre.

 

 

 

 

 

 

 

 

 

 

 

 

Cause:

The oven cavity gets too hot due to excessive

 

 

 

 

 

 

operation with no load or small load, or due to

 

 

 

 

 

 

some blocking materials around the Air Filter or

 

 

 

 

 

 

Air Exhaust at the back of the oven.

 

 

 

 

 

Remedy: • Open the oven door and check if 1) the oven

 

 

 

 

 

 

has been operating with no load or too small

 

 

 

 

 

 

load, 2) the air filter is placed in a wrong

 

 

 

 

 

 

position, or 3) any blocking materials exist

 

 

 

 

 

 

around the Air Exhaust. Cool down the oven (for

 

 

 

 

 

 

approx. 30 min) under the normal temperature.

 

 

Temperature of exhaust air too

 

one beep

 

The oven is back to normal when the error

 

 

E3

 

code “E3” disappears and “ON” appears again

 

 

High Error

for 2 sec

 

 

 

 

 

in the display window.

 

 

 

 

 

 

 

 

 

 

 

 

• Unplug the power cord, remove the blocking

 

 

 

 

 

 

materials around the ventilation openings, cool

 

 

 

 

 

 

down the oven (for approx. 30 min) sufficiently,

 

 

 

 

 

 

plug the power cord in again and check if the

 

 

 

 

 

 

error code appears again.

 

 

 

 

 

 

• If the symptom persists even when the oven is

 

 

 

 

 

 

cooled down sufficiently, contact the nearest

 

 

 

 

 

 

service centre.

 

 

 

 

 

 

 

 

 

 

 

 

Cause:

The circuitry inside the oven is not working correctly.

 

 

 

 

one beep

Remedy: Unplug the power cord and wait for 10 seconds.

 

 

HVT-I Power Error

E41

 

Plug the power cord in again and check if the

 

 

for 2 sec

 

 

 

 

 

 

error code “E41” appears again. If the symptom

 

 

 

 

 

 

 

 

 

 

 

 

persists, contact the nearest service centre.

 

 

 

 

 

 

 

 

 

 

 

 

Cause:

The circuitry inside the oven is not working correctly.

 

 

HVT-II Power Error

E42

one beep

Remedy: Unplug the power cord and wait for 10 seconds.

 

 

 

Plug the power cord in again and check if the

 

 

for 2 sec

 

 

 

 

 

 

error code “E42” appears again. If the symptom

 

 

 

 

 

 

 

 

 

 

 

 

persists, contact the nearest service centre.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

15

Page 15
Image 15
Samsung CM1219/XET, CM1219/XEF manual Error Codes, Error Items Code Error Beep Cause/Remedy