Samsung DVD-R4000EU manual Manually programming timer recordings, Press PROG/CHECK, Press Enter

Manually programming timer recordings

You can enter up to 16 programs up to a month in advance. Each daily or weekly program is counted as one program.

1	Press [PROG/CHECK].
		TIMER		Remaining Recording Time 1:58 SP
		RECORDING
						3/26TUE 12:55 PM
		No CHANNEL		DATE	ON	OFF	MODE CHECK
	A line that is	01	64 ABC	3/ 26 TUE	1:00 PM	2:00 PM	SP Enable
				New Timer Program
	ready for
	programming
	is highlighted.
		SELECT			Press ENTER or VCR Plus+ to
				CANCEL
2		ENTER	RETURN		store new program
	Press [ENTER].

TIMER
RECORDING	Remaining Recording Time	1:58 SP
	3/26TUE 12:55 PM

	CHANNEL		DATE	ON	OFF	MODE
	3		----------	--:-- --	--:-- --	--
	----4
						Enter Title
			Please set Channel.
SELECT				No.
		RETURN		0 --	9
ENTER

3 Press [1] to move through the items

and change the items with [3, 4].

≥The current settings are shown each time you press [1].

≥You may use the numbered buttons to enter the CHANNEL, DATE, ON (start Time), and OFF (Finish Time).

TIMER
RECORDING	Remaining Recording Time	1:58 SP
	3/26TUE 12:55 PM

CHANNEL DATE ON OFF MODE

64 ABC 3/ 26 TUE 2:30 PM 3:00 PM SP

Enter Title

≥CHANNEL (Channel number and caption)

≥DATE

Current date

;

Next day up to one month later minus one day

;

Weekly timer: SUN-SAT>MON-SAT>MON-FRI

;

Daily timer: WEEKLY SUN>--->WEEKLY SAT

;

(Return to Current date)

≥ON (Start time)/OFF (Finish time)

The time increases or decreases in 30-minute increments if you hold the button.

≥MODE (Recording mode ➜ page 15)

SP>XP>FR>EP>LP (>Return to SP)

≥Enter Title

Select “Enter Title” using [2, 1] and press [ENTER] (➜ page 27).

4 Press [ENTER] when you have finished programming the timer.

TIMER
				Remaining Recording Time				1:58 SP
RECORDING
						3/26TUE12:55 PM
		No	CHANNEL	DATE	ON	OFF	MODE	CHECK
		01	64 ABC	3/ 26 TUE	1:00 PM	2:00 PM	SP	Enable	Displayed if the
	02		64 ABC	3/ 26 TUE	2:30 PM	3:00 PM	SP	Enable
				New Timer Program					recording can fit
									in	the remain-
									ing	space on
									the disc.

≥Press [3, 4] to select “New Timer Program” and repeat steps 2- 4 to program other recordings.

5 Press [PROG/CHECK] or [RETURN].

The timer recording list disappears and the message “TURN RECORDER OFF FOR TIMER RECORDING” is shown on the television.

6 Press [Í, DVD POWER].

Ensure “ ” lights on the unit’s display.

To release the unit from recording standby

If you want to record something else before the program start time, for example:

Press [Í, DVD POWER].

The unit turns on and “ ” goes out.

≥Be sure to press [Í, DVD POWER] to return the unit to standby mode before the scheduled recording time. Timer recording will work only if “ ” is displayed.

To stop recording when recording has already begun

Press [∫], then [ENTER] within 5 seconds.

Recording stops.

[Note]

≥The actual time recorded may be longer than the program itself when television programs are recorded using VCR Plusi.

≥If you don’t select a recording mode when using VCR Plus+ codes to make a timer recording, the unit sets the mode selected on the unit at that time (unless the mode is “XP”, in which case the unit sets “FR” as the mode).

≥“All timer programs are occupied.” appears if there are already 16 programs.

≥The remaining time displayed is based on the current recording mode.

≥When you program successive timer recordings to start immediately one after the other, the unit cannot record the part at the beginning of the later programs (a few seconds when recording with DVD-RAM and approximately 30 sec- onds when recording with DVD-R).

≥If you set DST (Daylight Saving Time) to ON when manually setting the clock (➜ page 49), timer recording may not work when summer switches to winter and vice versa.

≥“ ” flashes when the unit couldn’t go to timer recording standby (e.g., a disc isn’t loaded, a disc that can’t be recorded to is loaded, or the disc is protected). Check the disc carefully.

Timer recording

25

DVD-R4000