Samsung M9T specification

Word	Content	Description
	3	1=Media Card Pass Through command feature set supported
	2	1=Media serial number supported
	1	1=SMART self-test supported
	0	1=SMART error logging supported

Command set/feature enabled. (The default manufacturing setting is as below) 15 Obsolete

14 1=NOP command enabled

		13	1=READ BUFFER command enabled
		12	1=WRITE BUFFER command enabled
		11	Obsolete
		10	1=Host Protected Area feature set enabled
		9	1=DEVICE RESET command enabled
85	7469h	8	1=SERVICE interrupt enabled
		7	1=Release interrupt enabled
		6	1=Look-ahead enabled
		5	1=Write cache enabled
		4	1=PACKET Command feature set enabled (Should be cleared to 0)
		3	1=Power Management feature set enabled
		2	1=Removable Media feature set enabled
		1	1=Security Mode feature set enabled
		0	1=SMART feature set enabled

Command set/feature enabled. 15-14 Reserved

			13	1=FLUSH CACHE EXT command supported
			12	1=FLUSH CACHE command supported
			11	1=Device Configuration Overlay features supported
			10	1=48 bit address feature supported
			9	Reserved
	86	BC41h	8	1=SET MAX security feature enabled by SET MAX SET PASSWORD
	86	BC41h	7	1=Set Address Offset Reserved Area Boot, INCITS TR27:2001
			7	1=Set Address Offset Reserved Area Boot, INCITS TR27:2001
			6	1= SET FEATURES subcommand required to spin-up after power-up.
			5	1=Power-Up Standby feature set enabled
			4	1=Removable media status notification feature set enabled
			3	1=Advanced Power Management feature set enabled
			2	1=CFA feature set enabled
			1	1=READ/WRITE DMA QUEUED supported
			0	1=DOWNLOAD MICROCODE command supported

Command set/feature default.

15Shall be set to 0

14Shall be set to 1

131=IDLE IMMEDIATE with UNLOAD FEATURE supported

12Reserved for technical report

11Reserved for technical report

101=URG bit supported for WRITE STREAM DMA EXT and WRITE STREAM EXT

9 1=URG bit supported for READ STREAM DMA EXT and READ STREAM

	87	6123h		EXT
	87	6123h	8	64-bit World wide name supported
			8	64-bit World wide name supported
			7	1=WRITE DMA QUEUED FUA EXT command supported
			6	1=WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT command
				supported

5 General Purpose logging feature set supported

41=Valid CONFIGURATION STREAM command has been executed

31=Media Card Pass Through command feature set enabled

21=Media serial number is valid

11=SMART self-test supported

01=SMART error logging supported

Spinpoint M9T Product Manual REV 1.0

52

Image 57

Samsung M9T manual =Media Card Pass Through command feature set supported

Contents

M9T Product Manual Page Table of Contents Iii Read Fpdma Queued 60h Read Log Extended 2Fh Read Long 22h Table of Tables Scope User DefinitionManual Organization Reference Sata Introduction Description Key Features Hardware Requirements Standards and Regulations Specification Summary Specifications Logical Configurations Physical Specifications Performance Specifications Power consumption Power consumptionPower Requirements Rated Environmental Specifications Environmental SpecificationsLinear Shock 1/2 sine pulse Rotational Shock Reliability Specifications Space Requirements Installation Mounting Unpacking Instructions Orientation Mounting Dimensions Cable Connectors VentilationSata Connectivity Computer mainboard or Serial ATA host adapter Management Power HDD Power, Sata Interface, and Factory Jumper Connector SATA-Bus Interface Connector DC Power Connector and SATA-Bus Interface Cable Connections Drive Installation Base Casting Assembly Head / Disk Assembly HDADC Spindle Motor Assembly Disk Drive Operation Exploded Mechanical View Head Stack Assembly Disk Stack AssemblyVoice Coil Motor and Actuator Latch Assemblies Air Filtration System Digital Signal Process and Interface Controller Drive ElectronicsDisk Controller DDR Buffer Control Block Host Interface Control Block Disk Control Block Disk Ldpc Control BlockFrequency Synthesizer Read/Write IC Power ManagementTime Base Generator Automatic Gain Control Analog to Digital Converter ADC and FIR Analog Anti-Aliasing Low Pass Filter Servo System Read and Write OperationsRead Channel Firmware Features Write ChannelRead Caching Write Caching Automatic Defect Allocation Defect ManagementSmart 6 APM Sata Terminology Sata II Interface Spinpoint M9T Product Manual REV Signal Descriptions Physical Interface Signal Summary 2 I/O Register Address When read When writtenControl Block Register Descriptions Registers Command Block Register Descriptions Device Register Ex F6h Command Register Ex F7h Status Register Ex F7h Device Activity Signal Sata II Feature SETStaggered Spin-up Disable Control Auto-Activate in DMA Setup FIS Phy Event Counters Sata Power Management Software Settings Preservation ATA Command Descriptions Command TableCommand Code Parameters Smart Check Power Mode E5h Command DescriptionsDevice Configuration Overlay B1h Download Micro Code 92h Device Configuration Identify data structure Word Content Diagnostic Codes Execute Device Diagnostics 90hFlush Cache E7h, EAh extended Format Track 50h Identify Device information Content Description =the fields reported in word 88 are valid EXT =Media Card Pass Through command feature set supported WWN Word Content Description Automatic Standby Timer Periods Idle E3hIdle Immediate E1h NOP 00h Initialize Device Parameters 91hRead Buffer E4h Read DMA C8h, 25h extended Read Multiple Command C4h, 29h extended Read Log Extended 2FhRead Long 22h Read Native Max Address F8h, 27h extended Read Sectors 20h, 24h extendedRead Verify Sectors 40h, 41h extended Recalibrate 10h Security Disable Password F6hSecurity Erase Prepare F3h Security Erase Unit F4h Security Erase Unit Password Word Content Security Set Password F1hSecurity Set Password data content Security Freeze Lock F5h Set Features EFh Security Unlock F2hSeek 7xh 12 Transfer Mode Values 11 Set Features Register Definitions 13 Set Max Feature Register Values Set Multiple Mode C6hSet Max Address F9h, 37h extended Sleep E6h Smart disable operations D9h 14 Smart Feature Registers ValuesSmart enable/disable attribute auto-save D2h Smart B0h Smart execute off-line immediate D4h Smart enable operations D8h 15 Device Smart Data Structure Smart read data D0h Byte 16 Smart Attribute Status Flags Bit Name Description 18 Off-line Data Collection Status Values 17 Smart Attribute Data List 19 Self-test Execution Status Values Self-test execution status byte Smart read log sector D5h Smart return status DAhSmart write log sector D6h Write Buffer E8h Standby Immediate E0hWrite DMA CAh, 35h extended Write Fpdma Queued 61h Write Sectors 30h, 34h extended Write Multiple Command C5h, 39h extended Spinpoint M9T Product Manual REV Maintenance Maintenance PrecautionsGeneral Information HDD handling guide -Please handle HDD by side surfaces HDD handling guide Prevent Shocks Service and Repair