Idle E3h, Idle Immediate E1h | Samsung M9T guide

Word	Content		Description
		2	1=Security locked
		1	1=Security enabled
		0	1=Security supported
129-159	0000h	Vendor specific
160	0000h	CFA power mode 1
161-175	0000h	Reserved for CFA
176-205	0000h	Current media serial number
206-254	0000h	Reserved
255	xxxxh	Integrity word
		15-8	Checksum
		5	Signature (A5h)

8.2.8Idle (E3h)

This command causes the drive to enter the Idle Mode, clear BSY, and generate an interrupt. The interrupt is generated even though the drive may not have fully transitioned to Idle Mode.

If the drive is already spinning, the spin-up sequence is not executed.

If the Sector Count register is non-zero, then the automatic Idle Mode sequence is enabled, and the timer begins counting down immediately. If the Sector Count register is zero, the automatic power down sequence is disabled.

After the drive enters Idle Mode, it automatically transitions to Standby Mode upon expiration of a prescribed 1 minute spin-down timer.

Table 8-6 Automatic Standby Timer Periods

Sector Count Register Contents		Corresponding Time-Out Period
0	(00h)	Timeout Disabled

1-240 (01h-FOh)		(value * 5) seconds

241-251 (F1h-FBh)		(value - 240) * 30 minutes

252	(FCh)	21 minutes

253	(FDh)	8 hours

254	(FEh)	Reserved

255	(FFh)	21 minutes 15 seconds

8.2.9Idle Immediate (E1h)

This command causes the drive to enter Idle Mode, clear BSY, and generate an interrupt. The interrupt is generated even though the drive may not have fully transitioned to Idle Mode.

Spinpoint M9T Product Manual REV 1.0

54

Image 59

Samsung M9T manual Idle E3h, Idle Immediate E1h, Automatic Standby Timer Periods

Contents

M9T Product Manual Page Table of Contents Iii Read Fpdma Queued 60h Read Log Extended 2Fh Read Long 22h Table of Tables Manual Organization ScopeUser Definition Reference Sata Introduction Description Key Features Hardware Requirements Standards and Regulations Specification Summary Specifications Logical Configurations Physical Specifications Performance Specifications Rated Power consumptionPower consumption Power Requirements Rotational Shock Environmental SpecificationsEnvironmental Specifications Linear Shock 1/2 sine pulse Reliability Specifications Space Requirements Installation Mounting Unpacking Instructions Orientation Mounting Dimensions Sata Connectivity Cable ConnectorsVentilation Computer mainboard or Serial ATA host adapter Management Power HDD Power, Sata Interface, and Factory Jumper Connector SATA-Bus Interface Connector DC Power Connector and SATA-Bus Interface Cable Connections Drive Installation Disk Drive Operation Head / Disk Assembly HDABase Casting Assembly DC Spindle Motor Assembly Exploded Mechanical View Air Filtration System Disk Stack AssemblyHead Stack Assembly Voice Coil Motor and Actuator Latch Assemblies Disk Controller Digital Signal Process and Interface ControllerDrive Electronics DDR Buffer Control Block Host Interface Control Block Frequency Synthesizer Disk Control BlockDisk Ldpc Control Block Automatic Gain Control Power ManagementRead/Write IC Time Base Generator Analog to Digital Converter ADC and FIR Analog Anti-Aliasing Low Pass Filter Read Channel Servo SystemRead and Write Operations Read Caching Firmware FeaturesWrite Channel Write Caching 6 APM Defect ManagementAutomatic Defect Allocation Smart Sata Terminology Sata II Interface Spinpoint M9T Product Manual REV Signal Descriptions Physical Interface Signal Summary Registers When read When written2 I/O Register Address Control Block Register Descriptions Command Block Register Descriptions Device Register Ex F6h Command Register Ex F7h Status Register Ex F7h Auto-Activate in DMA Setup FIS Sata II Feature SETDevice Activity Signal Staggered Spin-up Disable Control Phy Event Counters Sata Power Management Software Settings Preservation Command Code Parameters ATA Command DescriptionsCommand Table Smart Download Micro Code 92h Command DescriptionsCheck Power Mode E5h Device Configuration Overlay B1h Device Configuration Identify data structure Word Content Format Track 50h Execute Device Diagnostics 90hDiagnostic Codes Flush Cache E7h, EAh extended Identify Device information Content Description =the fields reported in word 88 are valid EXT =Media Card Pass Through command feature set supported WWN Word Content Description Idle Immediate E1h Automatic Standby Timer PeriodsIdle E3h Read DMA C8h, 25h extended Initialize Device Parameters 91hNOP 00h Read Buffer E4h Read Long 22h Read Multiple Command C4h, 29h extendedRead Log Extended 2Fh Read Verify Sectors 40h, 41h extended Read Native Max Address F8h, 27h extendedRead Sectors 20h, 24h extended Security Erase Unit F4h Security Disable Password F6hRecalibrate 10h Security Erase Prepare F3h Security Freeze Lock F5h Security Set Password F1hSecurity Erase Unit Password Word Content Security Set Password data content Seek 7xh Set Features EFhSecurity Unlock F2h 12 Transfer Mode Values 11 Set Features Register Definitions Sleep E6h Set Multiple Mode C6h13 Set Max Feature Register Values Set Max Address F9h, 37h extended Smart B0h 14 Smart Feature Registers ValuesSmart disable operations D9h Smart enable/disable attribute auto-save D2h Smart execute off-line immediate D4h Smart enable operations D8h 15 Device Smart Data Structure Smart read data D0h Byte 16 Smart Attribute Status Flags Bit Name Description 18 Off-line Data Collection Status Values 17 Smart Attribute Data List 19 Self-test Execution Status Values Self-test execution status byte Smart write log sector D6h Smart read log sector D5hSmart return status DAh Write Fpdma Queued 61h Standby Immediate E0hWrite Buffer E8h Write DMA CAh, 35h extended Write Sectors 30h, 34h extended Write Multiple Command C5h, 39h extended Spinpoint M9T Product Manual REV General Information MaintenanceMaintenance Precautions HDD handling guide -Please handle HDD by side surfaces HDD handling guide Prevent Shocks Service and Repair