Smart Attribute Data List | Samsung M9T specs

Each attribute data structure is assigned an attribute ID. Any non-zero value in the attribute ID number indicates an active attribute. Valid values for this byte are found from 0x01 through 0xff. The attribute defined for Spinpoint M9T are as follows:

Table 8-17 SMART Attribute Data List

Attribute ID	Definition	Monitor
1	Raw read error rate	Errors during read operations.
3	Spin up time	Spin up time in millisecond
4	Spindle motor on count	On/off count.
5	Number of Auto Reassign sectors	Reassigned sector count.
7	Seek error rate	Errors during seek operations.
8	Seek time performance	Off-line random seek time
9	Drive run time.	How long drive works.
10	Spin up retry count	Retry count
12	Power cycle count	Total power cycles.
194	Temperature.	Pre amp die temperature
195	ECC on the fly	ECC count for read operation
196	Re-allocate sector event	Read scan uncorrectable read error
197	Pending sector count	Off-line scan pending sectors
198	Uncorrectable sector count	Off-line scan uncorrectable sectors.
199	UDMA CRC error rate	CRC Errors during UDMA transfer
200	Write error rate	Errors during write operations.
201	Soft error rate	Soft errors during read operations.

Off-line data collection status

The value of the off-line data collection status byte defines the current status of the off-line activities of the device. Table6-15 lists the values and their respective definitions.

		Table 8-18 Off-line Data Collection Status Values

	Value	Definition
	00h or 80h	Off-line data collection activity was never started.

	01h	Reserved

	02h or 82h	Off-line data collection activity was completed without error.

	03h	Reserved

	04h or 84h	Off-line data collection Activity was suspended by an interrupting command from host

	05h or 85h	Off-line data collection Activity was aborted by an interrupting command from host

	06h or 86h	Off-line data collection Activity was aborted by the device with a fatal error.

	07h-3Fh	Reserved

	40h-7Fh	Vendor specific

	81h	Reserved

	83h	Reserved

	87h-BFh	Reserved

	C0h-FFh	Vendor specific


	Spinpoint M9T Product Manual REV 1.0		68

Image 73

Samsung M9T manual Smart Attribute Data List, Off-line Data Collection Status Values

Contents

M9T Product Manual Page Table of Contents Iii Read Fpdma Queued 60h Read Log Extended 2Fh Read Long 22h Table of Tables User Definition ScopeManual Organization Reference Sata Introduction Description Key Features Hardware Requirements Standards and Regulations Specification Summary Specifications Logical Configurations Physical Specifications Performance Specifications Power consumption Power consumptionPower Requirements Rated Environmental Specifications Environmental SpecificationsLinear Shock 1/2 sine pulse Rotational Shock Reliability Specifications Space Requirements Installation Mounting Unpacking Instructions Orientation Mounting Dimensions Ventilation Cable ConnectorsSata Connectivity Computer mainboard or Serial ATA host adapter Management Power HDD Power, Sata Interface, and Factory Jumper Connector SATA-Bus Interface Connector DC Power Connector and SATA-Bus Interface Cable Connections Drive Installation Base Casting Assembly Head / Disk Assembly HDADC Spindle Motor Assembly Disk Drive Operation Exploded Mechanical View Head Stack Assembly Disk Stack AssemblyVoice Coil Motor and Actuator Latch Assemblies Air Filtration System Drive Electronics Digital Signal Process and Interface ControllerDisk Controller DDR Buffer Control Block Host Interface Control Block Disk Ldpc Control Block Disk Control BlockFrequency Synthesizer Read/Write IC Power ManagementTime Base Generator Automatic Gain Control Analog to Digital Converter ADC and FIR Analog Anti-Aliasing Low Pass Filter Read and Write Operations Servo SystemRead Channel Write Channel Firmware FeaturesRead Caching Write Caching Automatic Defect Allocation Defect ManagementSmart 6 APM Sata Terminology Sata II Interface Spinpoint M9T Product Manual REV Signal Descriptions Physical Interface Signal Summary 2 I/O Register Address When read When writtenControl Block Register Descriptions Registers Command Block Register Descriptions Device Register Ex F6h Command Register Ex F7h Status Register Ex F7h Device Activity Signal Sata II Feature SETStaggered Spin-up Disable Control Auto-Activate in DMA Setup FIS Phy Event Counters Sata Power Management Software Settings Preservation Command Table ATA Command DescriptionsCommand Code Parameters Smart Check Power Mode E5h Command DescriptionsDevice Configuration Overlay B1h Download Micro Code 92h Device Configuration Identify data structure Word Content Diagnostic Codes Execute Device Diagnostics 90hFlush Cache E7h, EAh extended Format Track 50h Identify Device information Content Description =the fields reported in word 88 are valid EXT =Media Card Pass Through command feature set supported WWN Word Content Description Idle E3h Automatic Standby Timer PeriodsIdle Immediate E1h NOP 00h Initialize Device Parameters 91hRead Buffer E4h Read DMA C8h, 25h extended Read Log Extended 2Fh Read Multiple Command C4h, 29h extendedRead Long 22h Read Sectors 20h, 24h extended Read Native Max Address F8h, 27h extendedRead Verify Sectors 40h, 41h extended Recalibrate 10h Security Disable Password F6hSecurity Erase Prepare F3h Security Erase Unit F4h Security Erase Unit Password Word Content Security Set Password F1hSecurity Set Password data content Security Freeze Lock F5h Security Unlock F2h Set Features EFhSeek 7xh 12 Transfer Mode Values 11 Set Features Register Definitions 13 Set Max Feature Register Values Set Multiple Mode C6hSet Max Address F9h, 37h extended Sleep E6h Smart disable operations D9h 14 Smart Feature Registers ValuesSmart enable/disable attribute auto-save D2h Smart B0h Smart execute off-line immediate D4h Smart enable operations D8h 15 Device Smart Data Structure Smart read data D0h Byte 16 Smart Attribute Status Flags Bit Name Description 18 Off-line Data Collection Status Values 17 Smart Attribute Data List 19 Self-test Execution Status Values Self-test execution status byte Smart return status DAh Smart read log sector D5hSmart write log sector D6h Write Buffer E8h Standby Immediate E0hWrite DMA CAh, 35h extended Write Fpdma Queued 61h Write Sectors 30h, 34h extended Write Multiple Command C5h, 39h extended Spinpoint M9T Product Manual REV Maintenance Precautions MaintenanceGeneral Information HDD handling guide -Please handle HDD by side surfaces HDD handling guide Prevent Shocks Service and Repair