Samsung RF24FSEDBSR Completing the SET UP, Connecting the water supply line to the refrigerator

3.Connect the water line installation kit to the shut off valve.

Cold water line

Water line installation kit Pipe clamp

Shut off valve

Connecting the water supply line to the refrigerator.

There are several items that you need to purchase to complete this connection.

You may find these items sold as a kit at your local hardware store.

Use Copper Tubing		Use Plastic Tubing
•	¼” copper tubing	•	¼” plastic tubing
•	¼” compression nut		→ Molded end(Bulb)
	(1pc)	•	¼” compression nut
•	Ferrule (2pc)		(1pc)

Refrigerator

Plastic Tubing

Compression		(Assembled)
Nut (1/4”)
		Compression
(Assembled)
		Fitting
		(Assembled)
Ferrule		Molded
		end(Bulb)
(Not supplied)
		Compression
		nut (B) (1/4”)
		(Not supplied)
Copper tubing	or	Plastic tubing (B)
(Not supplied)		(Not supplied)

Household water supply line

1.Connect the household water line to the assembled compression fitting.

-- If you are using copper tubing, slip the compression nut ( B ) (not supplied) and ferrule (not supplied) on the copper tubing (not supplied) as shown.

-- If you are using plastic tubing ( B ) , insert the molded end (Bulb) of the plastic tubing ( B ) into the compression fitting.

Do not use without the molded end (Bulb)

CAUTION

of the plastic tubing ( B ).

2.Tighten the compression nut ( B ) onto the compression fitting.

Do not over-tighten the compression nut ( B ) .

3.Turn the water on and check for any leakage. If you find water drops or leakage in the connection areas, turn off the main water supply. Check the connections and, if necessary, tighten.

4.Flush 1 gallon of water through the filter before drinking or using the water from the refrigerator. (Flush approximately 6 minutes.) To flush, press a large glass or cup against the water dispenser lever. Fill the glass, empty it into the kitchen sink after it is filled, and then repeat.

5.After you turn on the refrigerator, let the ice maker make ice for 1 to 2 days. Over that period of time, throw out the first 1 or 2 buckets of ice the freezer makes to ensure all impurities have been removed from the water line.

Only connect the water line to a drinkable water source.

If you have to repair or disassemble the water line, cut off 1/4“ of the plastic tubing to make sure you get a snug, leak-free connection.

You can test the water line quickly using a paper cup. Under normal conditions, the water dispenser can fill a 5.75 oz. (170cc) cup in about 10 seconds.

COMPLETING THE SET UP

Now that you have your new refrigerator installed in place, you are ready to set up and enjoy the features and functions of the appliance.

By completing the following steps, your refrigerator should be fully operational.

1.Make sure your refrigerator is in an appropriate location with reasonable clearance between it and the wall. Refer to installation instructions in this manual.

2.Once the refrigerator is plugged in, make sure the interior light comes on when you open the doors.

3.Set the Temperature control to the coldest temperature and wait for an hour. The freezer will get slightly chilled and the motor will run smoothly. Reset the refrigerator and freezer to the temperatures you want.

4.After you plug the refrigerator in, it will take a few hours to reach the appropriate temperature. You can store food and drinks in the refrigerator after the temperature is sufficiently cool.

If condensation or water drops appears on both sides of fridge door’s central part, turn the Energy Saver mode off after removing the condensation. (See the explanation on Energy Saver button in the USING THE CONTROL PANEL.)

up 01setting

setting up _15