Operating your French Door Refrigerator
USING THE CONTROL PANEL
RF24FS**
( 3 ) | The Alarm button serves two purposes: | |
Alram | To turn the door open alarm on and off | |
(Hold 3 | To reset the water filter life indicator. | |
sec for | 1) | Door Alarm Function |
Filter | If the door alarm is set to On, an alarm | |
Reset | beeps if any refrigerator door is left open |
1
2
3
10 7
4
5
6
9 8
for more than three minutes. The beeping |
stops when you close the door. The door |
alarm function is |
factory. You can turn it off by pressing and |
then releasing the Alarm button. You can |
turn it back on in the same fashion. The |
icon lights up when the function is on. |
When the Door Alarm function is on and |
the alarm sound is triggered, the Door |
Alarm Icon will blink while the alarm |
sounds. |
( 1 ) | Touching this button turns Energy Saver | |
Energy | ||
mode on and off. When you turn Energy | ||
Saver | ||
Saver on, the Energy Saver icon lights. | ||
| Turn Energy Saver off and the icon goes | |
| off. The Energy Saver function’s factory | |
| setting is “ON”. If condensation or water | |
| drops appear on the doors, turn the | |
| Energy Saver mode off. |
( 2 ) | The Freezer button serves two purposes: | |||
Freezer | To set the Freezer to your desired | |||
(Hold 3 |
| temperature. | ||
sec for | To turn the power freezer function on | |||
Power |
| and off. | ||
Freezer) | 1) To set the Freezer temperature | |||
|
|
| Touch the Freezer button to set the | |
|
|
| Freezer to your desired temperature. You | |
|
|
| can set the temperature between 5 °F | |
|
|
| ||
|
|
| 2) Power Freezer function | |
|
|
| Touch and hold this button for 3 seconds | |
|
|
| to decrease the time needed to freeze | |
|
|
| products in the Freezer. | |
|
|
| It can be helpful if you need to quickly | |
|
|
| freeze easily spoiled items or if the | |
|
|
| temperature in the freezer has warmed | |
|
|
| ||
|
|
| dramatically (For example, if the door was | |
|
|
| left open). | |
|
|
| When you use this function the energy | |
|
|
| consumption of the refrigerator will | |
|
|
| increase. Remember to turn it off when | |
|
|
| you don’t need it and return the freezer | |
|
|
| to your original temperature setting. If you | |
|
|
| need to freeze large amount of food stuff, | |
|
|
| activate Power Freeze function at least 24 | |
|
|
| hours before. | |
|
|
|
|
|
| 2) Water Filter Life Indicator Function | |
| After you replace the water filter, touch | |
| and hold this button for 3 seconds to | |
| reset the water filter life indicator. When | |
| you reset the water filter life indicator, the | |
| Filter icon on the panel turns Off. The | |
| Filter icon will turn red to let you know it | |
| is time to change the water filter after six | |
| months (about 300 gallons). Some areas | |
| have large amounts of lime in their water, | |
| which causes the water filter to clog more | |
| quickly. If this is the case in your area, | |
| you will have to change the filter more | |
| frequently than every six months. | |
|
| |
|
| |
( 4 ) | Lighting button serves two purposes: | |
Lighting | To turn the dispenser light on and off | |
(Hold 3 | To switch the temperature units | |
sec for ºC |
| between ºC and ºF |
↔ºF) 1) Light Function
Touching the Lighting button turns on the Dispenser LED lamp in continuous mode so that it stays on continuously.
The button also lights up. If you want the Dispenser lamp to come on only when some one uses the dispenser, press the Lighting button to turn the continuous mode off.
2) To switch the temperature units between ºC and ºF
Touch and hold this button for 3 seconds to select the temperature display you want.
Each time you press and hold the button, the ºC and ºF temperature modes alternate and the ºC or ºF icon lights up, indicating your selection.