Needed, SET-AUTO SET are not available | Samsung SCC-C6453N specs

setup

-NIGHTDAY DWELL TIME : Time required to determine the filter switch.

-MASK AREA : If there exists a bright

spot light source in a night scene, you MASK AREA

can specify the size and position as	<SIZE>
needed.	<LOCATION>
This will prevent an error in switching
filter, or failure to determine the filter
switch in a night scene where a bright
spot light source exists.
Any excessively bright area in a night
scene will be MASKed.

You can specify MASK 1 and 2 simultaneously.

If <BACKLIGHT> is set to <BLC>, the MASK AREA function is not available.

EXT : The interface to an external alarm enables an automatic switch between DAY and NIGHT mode.

If you set <DAY/NIGHT> to EXT, and alarm #1 to NO/NC in ALARM SET- ALARM IN SET, the alarm can be used for an input signal in EXT mode of <DAY/NIGHT>.

If an alarm signal occurs, the mode will switch to NIGHT.

M 	If <DAY/NIGHT> is set to EXT, ALARM1 in ALARM OUT SET, and ALARM1 in ALARM
	SET-AUTO SET are not available.
	If you use an infrared light source while in AUTO mode, this may cause a failure in
	AUTO SWITCH or AUTO FOCUS.

28_ setup

00890A-NA_SCC-C6453N-ENG.indb 28

2009-08-05 오후 3:03:

Image 28

Samsung SCC-C6453N user manual Needed, SET-AUTO SET are not available, Auto Switch or Auto Focus

Contents

Smart Dome Camera Overview English Overview FCC Statement Important safety instructions Contents Features What’s Included Camera At a GlanceFrame SET Preparing Installation Installation Screw Fixing Hole Diagram Insert the cable into the Frame SET, and close the Adaptor Protective Tape from on the lens Button Frame SET Cover Camera Initial Setup Camera Address SetupCommunication Protocol Setup Use SW606, SW605, and SW604 to specify the camera address Baud Rate Setup Setting RS-422A/RS-485 TerminationUse pins #5, #6 of SW603 to set the baud rate Factory default is 9600 BPS RS-422A/RS-485 Full Duplex Organization Same address in the network Connecting to a monitor Connecting with Other deviceVideo terminal on the rear of monitor BNC Cable To connect Alarm OUT To connect AlarmTo connect the controller Power Supply Connecting the adaptor cableAdaptor Board Using OSD icons How to use the keyboard controllerCamera will resume the last run operation Main Menu Profile  ITS Night You can configure the general settings of the camera module Camera SETCamera ID  Location Specify the display position of the camera ID  Manual Adjust the iris level manually With this, you can adjust the AGC level of aIris AGC Motion DNRShutter SENS-UP You can specify a recording mode according to the scene FlickerlessXDR DAY/NIGHT Needed Auto Switch or Auto FocusSET-AUTO SET are not available White BAL DAY/NIGHT Zoom Speed Display ZoomDisplay P/T Digital Zoom Sync AGC Color SUPReverse POSI/NEGA You can enable the motion detection and tracking functions When multiple motions continue arbitrarilyIntelligent Video Advanced Resolution Alarm OUTPrivacy Zone Display Preset Select the preset number Select Position and adjust PAN Auto Pan Setup Settings so define them again after the operationAuto SET You can set the Auto PAN, PATTERN, and Auto Play Position Direction Left Endless OFF Speed Scan Setup Pattern SetupSelect the Start and move the camera using pan/tilt/zoom Auto Play Setup ~ 511 for Preset You can set the north direction and the zone coverage Zone SETSelect Main MENU-ZONE SET Alarm SET Select Main MENU-ALARM SET  Auto SET Sets the pattern and scan Clock SET Other SET Factory Defaults PasswordOSD Color Proportional P/T Communication System InfoYou can check the system information Select Main MENU-SYSTEM Info Language You can set the language of the user interface Shortcut Keys Function Key Specifications Preset Pan Speed 600˚/sec, maximum Description PAN range 360˚EndlessManual Pan Speed 0.01˚~ 180˚/sec Tilt range -6˚~186˚ Product Appearance 00890A-NASCC-C6453N-ENG.indb 2009-08-05 오후