FRANÇAISENGLISH
65
Checking VérificationTroubleshooting
Dépannage
✤If you run into any problem using the camcorder, use the
following table to troubleshoot the problem.
✤If these instructions do not allow you to solve the problem,
take a note of:
■The model and serial number marked on the bottom of the
camcorder.
■Your warranty, if applicable.
✤Then contact your nearest authorized service center.
Symptom Explanation/Solution
You cannot switch the ◆Check the battery pack (see page 19)
camcorder on. or the AC power adapter. (see page 18)
Start/Stop does not ◆Check the POWER, set it to CAMERA.
operate while shooting. ◆You have reached the end of the cassette.
◆Check the record protection tab on the
cassette. (see page 22)
The camcorder goes ◆You have left the camcorder set to STANDBY
off automatically. for more than 5 minutes without using it.
(see page 24)
◆The battery pack is fully used up.
(see page 21)
The battery pack is ◆The atmospheric temperature is too low.
quickly exhausted. (see page 21)
◆The battery pack has not been charged fully.
(see page 19)
◆
The battery pack is completely dead, and
cannot be recharged. Use another battery pack.
You cannot eject the ◆The battery pack is fully used up.
cassette from the ◆Amechanical fault might have occurred.
compartment. (see page 64)
The DATE/TIME indicator ◆The lithium battery is not installed or is
flashes more than 2 times fully used up. (see page 17)
when you set the
camcorder to CAMERA.
The playback picture ◆
The video heads might be dirty. (see page 62)
is poor.
You cannot operate any ◆Amechanical fault might have occurred.
functions on the camcorder. (see page 64)
✤Pour résoudre un problème rencontré lors de l’utilisation de
votre caméscope, consultez le tableau ci-dessous.
✤Si ces instructions ne vous permettent pas de résoudre le
problème, notez:
■la référence du modèle et le numéro de série indiqués
sous le caméscope,
■votre numéro de garantie, si elle est toujours valable.
✤Puis, contactez votre SAV ou le revendeur le plus proche.
Symptôme Explication/Solution
Vous ne pouvez pas ◆Vérifiez le bloc batterie (voir page 19)
allumer le caméscope. ou l’adaptateur secteur. (voir page 18)
La touche ◆Vérifiez que le commutateur principal est en
START/STOPne position CAMERA.
fonctionne pas lors ◆Vous avez atteint la fin de la cassette.
de l’enregistrement. ◆Vérifiez la languette de protection
sur la cassette. (voir page 22)
Le caméscope s’éteint ◆Vous avez laissé le caméscope sur STANDBY
automatiquement. pendant plus de 5 minutes sans l’utiliser.
(voir page 24)
◆Le bloc batterie est complètement déchargé.
(voir page 21)
Le bloc batterie se ◆La température ambiante est trop basse.
décharge rapidement. (voir page 21)
◆Le bloc batterie n’a pas été complètement
rechargé. (voir page 19)
◆Le bloc batterie n’est plus utilisable et ne peut
plus être rechargé. Utilisez un autre bloc batterie.
Vous ne pouvez pas ◆Le bloc batterie est complètement déchargé.
éjecter la cassette de ◆Une erreur mécanique s’est peut-être produite.
son compartiment. (voir page 64)
La date et l’heure ◆La pile au lithium n’est pas installée ou
clignotent plus de 2 fois est complètement déchargée. (voir page 17)
en mode Camécope.
La lecture de l’image ◆Les têtes vidéo sont peut-être sales.
n’est pas de bonne (voir page 62)
qualité.
00607C SCL810-USA+FRA(46-71) 7/3/03 11:30 AM Page 65