Sanyo DP32671, DP36671, DP26671 manual Preparation, Status display of disc, Playback procedure

Insert the AC cord plug into a standard 120V 60Hz polarized AC outlet.

• If the AC cord plug is plugged in for the first time, wait for about 5 seconds before pressing

POWER.

NOTE:

• When connecting to other equipment, unplug the unit from the AC outlet.

Press POWER on the unit or on the remote control to turn on the unit. The POWER indicator will change to green.

• Each time you turn the unit ON, the TV/DVD starts from the TV mode.

• When using an amplifier, switch on the amplifier. Press TV/DVD to select DVD mode.

The DVD startup screen will appear on the screen.

Preparation

The following pages describe the setup/ operation in DVD mode.

Preparation

Before DVD/CD operation, please make the following preparations.

1

2

3

NOTE:

• If the unit does not operate properly: Static electricity, etc., may affect the player’s operation. Disconnect the AC power cord once, then connect it again.

• About inserting disc:

If the unit is slanted or moved while inserting disc, the disc may get damage.

Status display of disc

Press DISPLAY. The status display of the disc will appear on the screen

• Display messages may change at every time when you press DISPLAY for some discs or files.

To make the status display screen disappear, press DISPLAY again.

Playback procedure

1 Press TV/DVD to select DVD mode.

2 Place the disc in the disc slot with the label

side facing forward. (If the disc has a label.) Hold the disc without touching either of its

surfaces, align it with the guides, and place it in position.

		On the screen, “ ” changes to “Loading” and then
3 playback will commence.
		• A menu screen may appear on the TV screen,
			if the disc has a menu feature. In this case,
			press ▲, ▼, ◀, ▶ or ENTER to operate a menu
			feature.
4						ENGLISH
		Press STOP (		) to end playback.
		•	The unit can record where you stop a video, but it
			depends on a disc you are using. Press PLAY
			( ) to resume a playback point. The unit can
			store a memory of stopped point of last five discs
			that you have played. When one of these discs
			is next loaded, you can resume playback from
			where you stopped playing last time.
		•	If you press STOP (		) again (“Resume off”
			appears on the screen) the unit will clear the
		•	stopped point.
			You cannot save a stopped point for some discs.
			If a number of discs played and stored in the unit
			exceeds five, a new memory will overwrite the old
5			stored memory.
		Press (EJECT).
		Remove the disc and then press POWER.
		The unit turns off.
		•	When you eject the disc, you may hear
			mechanism noise, but it is not malfunction.
NOTE:
•	If a non-compatible disc is loaded, “Can’t play disc”
	or “Incompatible disc region number Can’t play
	disc” will appear on the TV screen according to the
	type of loaded disc. In this case, check your disc
•	again (see page 11).
	Some discs may take a minute or so to start
•	playback.
	A prohibition message “Depending on the disc, this
	operation may be prohibited” or “This operation
	can’t be performed” may appear at the screen. This
	message means either the feature you tried is not
	available on the disc, or the unit cannot access
	the feature at this time. This does not indicate a
•	problem with the unit.
	When you set a single-faced disc label downwards
	(i.e. the wrong way up) “Loading” will appear on the
•	display and then “Can’t play disc” will be displayed.
	Some playback operations of DVDs may be
	intentionally fixed by software producers. Since
	this unit plays DVDs according to the disc content

recorded, some playback features may not be available. Also refer to the instructions supplied with the DVDs.

25

56Q0221A_eng.indd 25

1/11/11 3:24:29 PM