Using the Multimedia Remote Control

It takes only one remote to operate your TV and other equipment. Simply follow the instructions on pages 13 ~ 15.

Install Batteries as shown (2 AA, not included)

Notes:

Do not mix old batteries with new ones or mix different types of batteries together.

Remove the batteries if the remote control will not be used for a month or more. Weak batteries may leak and cause damage. (Normal battery life is roughly six months.)

 

Point towards TV / Equipment

 

 

 

 

 

➠

 

 

 

 

➀

VCR

TV

CABLE

 

 

DVD

SAT

AUX

 

 

 

 

 

 

INPUT

POWER

RESET

 

➁

 

11

 

 

 

 

 

 

 

 

➂

 

1

2

3

 

 

 

 

 

4

5

6

 

 

 

 

➃

 

 

 

 

 

 

7

8

9

 

 

 

 

 

 

 

 

 

 

➄

TUNER

0

MUTE

 

 

12

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

➅

 

 

CH

 

VOL

 

 

 

 

 

 

 

 

 

 

 

 

 

➆

PIX SHAPE

SLEEP

AUDIO

 

 

13

➇

RECALL

CAPTION

INFO

 

 

 

14

➈

M E

N

U

 

 

 

 

 

 

 

 

 

 

 

 

 

 

15

➉

 

 

 

ENTER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X

I

T

 

 

 

 

 

 

E

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

N

PAGE

UP

 

 

 

16

 

DOW

GUIDE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PLAY

 

 

 

 

 

 

REC

STOP

PAUSE

17

 

ON/OFF

 

QUIK

 

 

 

 

 

PAP

 

FREEZE

 

 

18

 

SWAP

 

 

 

 

 

 

 

 

 

 

 

 

PAP CHANNEL

➀Mode Keys—Use these keys to program the remote control and to select the operating mode (VCR, TV, CABLE, DVD, SAT, or AUX). To Operate Your...

VCR—Press the VCR key; Television—Press the TV key; Cable Box—Press the CABLE key; DVD Player—Press the DVD key; and Satellite Receiver—Press the SAT key.

Note: Make sure you hold down the mode key while entering a code number, see page 13.

➁Input Key—Press this key to change the input signal source as follows:

RF

 

DIGITAL RF

 

 

VIDEO

1

VIDEO

2

 

 

 

 

 

 

 

 

ANALOG

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DMI

 

 

 

COMPO 3

 

 

COMPO 2

 

In the TV, DVD, Cable, and Satellite modes, this key selects the program source to display on the screen (TV signal or signal from equipment connected to the AV jacks). In the VCR mode, this key functions as a VCR’s TV/VCR key.

➂Power Key—Press to turn TV on or off.

➃Number Keys—Two keys must be pressed to select a direct channel. Example: Press 0 then 6 to select channel 6. For Analog channels above 100, press and hold the 1 key until C1–– appears.

➄Tuner Key—Use this key to toggle from one tuning system to another, digital channels and analog channels.

➅Channel (CH up / down) and Volume (VOL – /+) Keys—PressUp/down keys to tune to the next higher or lower channel in the Channel Scan Memory database. Press the – /+keys to adjust volume. The screen displays a left or right red arrow that blinks as many time as you press the Vol –/+keys.

➆Pix Shape Key—Use this key to change the video display format. Available options depend on signal received and the broadcast aspect ratio: For HT27744/ HT32744—Letter box, Zoom, and Normal. For HT30744—Full, Zoom1/2, and Normal. (See explanation of image shapes on page 5.) Note: If PAP feature is selected, this key is not operable.

➇Sleep Key—Press this key, then press the “0” key to set the Sleep Timer. The desired time can be set from 30 minutes up to 3 hours in 30 minutes increments. Sleep Timer will switch off the TV automatically.

Note: The Sleep Timer cancels when the TV is turned off or if a power failure occurs.

➈Recall Key—Select the first channel you want to watch; then select another channel using the number keys. Press Recall to easily switch between the channels without entering the channel numbers again.

Note: The Recall key can only toggle between channels within the same signal source. Recall between a Digital channel and an Analog channel will

not work.

12 Remote Control