If “OUTPUT” is set to “NON REC”, please continue with step 4.

OUTPUT TERMINALS

SERIES OUT/NON REC OUT terminal

ACTIVE HIGH . . Normally 0V are output between

setting

the SERIES OUT/NON REC OUT

and theCOM terminals. If during

The output at theSERIES OUT/NON REC OUT terminal

recording the VCR enters a mode

can be set.

other than recording (i.e.

1 PressMENUthebutton until the (SET UP 5) menu is

recording pause, stop mode, etc.),

the output become 5 V (High). If

displayed.

recording is resumed, then the

NOTE:

output become 0 V (Low).

• Ιφ“OUTPUT” is set to “NON REC”, the “NON REC

NOTES:

 

OUT” line will be displayed under the “OUTPUT”

 

• Ιφ“NON REC OUT” is set to “ACTIVE HIGH”, a

line.

throwaway pulse will be output from the SERIES

@@@@@@@<SET@UP@5>

OUT/NON REC OUT terminal when power is

*INPUT@OUTPUT@ALARM

*OUTPUT@@@@@@@SERIES

restored after an outage, when the power is turned

*NON@REC@OUT@@ACTIVE@LOW

*WARN.@OUT@@@@TRANSPORT

on or when theALL RESET button is pressed. This

 

*REMOTE@@@@@@@EJECT

will continue until the microprocessor starts

*TAPE@@@@@@@@@T-160

 

operating. If this output terminal is connected to

 

some other device, the device should be set or

2 Press] thebutton,“OUTPUT”untilsettingtheis

adjusted so that it is not affected by the throwaway

flashing.

pulse. If set to“ACTIVE LOW”, this kind of pulse is

 

not output, and so it is recommended that you use

3 Pressl the(orj) button, to select the desired

 

output mode.

the “ACTIVE LOW” setting.

• Ιφ ιν τηε (ΣΕΤ ΥΠ 2) ∝ενυ, ιν“BUZZER”τηε

SERIES . .SERIES. .OUT/NON. TheREC

section, “WARNING” is set to “Y”, a buzzer will be

OUT terminal will be set to

heard while the VCR is in non recording mode. The

SERIES OUT.

buzzer will stop if the STOP button is pressed (the

If during series recording, the

output signal will remain).

counter reading reaches 7:57:00

6 PressPAUSE/SEARCHthe

button to save the setting.

or the tape reaches the end, a

LOW signal (0 V) is output. The

 

 

LOW (0 V) signal is output for

ALARM IN/CLOCK IN and ALARM

about 70 seconds after the end of

the tape is reached.

OUT/CLOCK OUT terminal setting

NON REC . . . The SERIES OUT/NON REC OUT terminal will be set toNON

REC OUT.

1PressMENUthebutton until the (SET UP 5) menu is displayed.

°The “INPUT OUTPUT” setting is flashing.

2Pressl the(orj) button to select d input/output mode.

4 Press] thebutton.

ALARM. . .ALARM. IN/CLOCK. . TheIN

 

terminal is set toALARM IN and

5 Pressl the(orj) button to select the desired output.

ACTIVE LOW . . Normally DC 5V are output

the ALARM OUT/CLOCK OUT

terminal is set toALARM OUT.

between the SERIES OUT/NON

CLOCK SET. . The ALARM IN/CLOCK IN

REC OUT and theCOM

terminal is set toCLOCK IN and

terminals. If during recording the

the ALARM OUT/CLOCK OUT

VCR enters a mode other than

terminal is set toCLOCK OUT.

recording (i.e. recording pause,

3 PressPAUSE/SEARCHthe

button to save the setting.

stop mode, etc.), the output

become 0 V (Low). If recording is resumed, then the output become 5 V (High).

English

41