Barracuda 4LP Installation Guide, Rev. B | 39 |
N drives
Other applicable jumper options
Several other jumper options are available as illustrated.
Drive with |
|
|
|
|
|
|
|
|
|
| ||
HDA up, PCB |
|
|
|
|
|
|
|
|
|
| ||
down, viewed |
|
|
|
| Pin 1 |
| ||||||
from front | HDA |
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| J6 |
|
|
|
| L | R | R |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| |||
|
| Reserved E | E | E A | 2 | A | 1 | A | 0 |
|
| |
|
|
| D | S | S |
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| |||
Reserved |
|
11 |
|
Remote |
|
LED | CATH |
12 |
Shipped with cover installed.
Do not remove.
Do not install jumpers on these four positions.
| J2 |
|
|
|
|
| Pin 1 |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
Reserved |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Delay Motor Start option |
|
|
|
|
|
| |
(valid only if the Enable |
|
|
|
|
|
| |
Motor Start jumper is |
|
|
|
|
|
| |
not connected) |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
Disable the Delay Motor |
|
|
|
| (default) | ||
Start option. |
|
|
|
| |||
|
|
|
|
|
| ||
Motor start delay equal |
|
|
|
|
|
| |
to the SCSI ID multiplied |
|
|
|
|
|
| |
by 12 seconds. For |
|
|
|
|
|
| |
example, if the SCSI |
|
|
|
|
|
| |
ID = 2, the drive starts |
|
|
|
|
|
| |
in 24 seconds. |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
Motor Start option |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Disable motor start. |
|
|
|
|
|
| |
Drive Front | J6 |
|
J2 
DC Power
Connector
J1
J6
Jumper Type (enlarged to show detail)
Pin 1
End
Pin 1
The drive starts | (default) | |||||||
according to the | ||||||||
| ||||||||
Delay Motor Start option. |
| |||||||
|
| |||||||
Enable motor start. The |
| |||||||
drive waits for the Start |
| |||||||
Unit command from the |
|
|
|
|
| |||
host before starting the |
|
|
| |||||
|
|
| ||||||
spindle motor. |
| |||||||
|
|
|
|
|
|
|
| |
Write Protect option |
|
|
|
|
| |||
Write protect = Off |
|
|
| (default) | ||||
(enables writing). |
|
|
|
|
| |||
|
|
|
| |||||
Write protect = On |
|
|
|
|
|
| ||
(disables writing). |
|
|
|
|
|
| ||
|
|
| ||||||
|
|
|
|
|
|
|
| |
Parity Check option |
|
|
|
|
|
|
| |
Enable parity check of | (default) | |||||||
SCSI bus. | ||||||||
SCSI I/O
Connector J2 Jumper Type (enlarged to
show detail)
Disable parity check. |
