Sears 139.53960SRT, 139.53968SRT Install the Door Control, Llilllllliltltl Illliillllil

INSTALLATION STEP 6

Install the Door Control

Locate door control within sight of door, at a minimum height of 5 feet where small children cannot reach, away from moving parts of door and door hardware.

If installing into drywall, drill 5/32" holes and use the anchors provided. For pre-wired installations (as in

new home construction), it may be mounted to a single gang box (Figure 2).

1.Strip 1/4" of insulation from one end of bell wire and connect to the two terminal screws on back of door

control by color: white to 2 and white/red to 1.

2.Door Control Button: Fasten securely with 6ABx1-l/2" screws.

Console Model: Pry off cover along one side with a screwdriver blade (see Figure 1). Fasten with 6ABx1-1/4"self-tapping screws (standard

installation) or 6-32x1" machine screws (into gang box) as follows:

•Install bottom screw, allowing 1//8" to protrude above wall surface.

•Position bottom of door control on screw head and slide down to secure. Adjust screw for snug fit.

•Drill and install top screw with care to avoid cracking plastic housing. 13onot overtighten.

•Insert top tabs and snap on cover.

3.(For standard installation only) Run bell wire up wall and across ceiling to motor unit. Use insulated staples to secure wire in several places. Be careful not to pierce wire with a staple, creating a short or open circuit.

4.Connect the bell wire to the terminal screws on the motor unit panel: white to 2; white/red to 1.

5.Position the antenna wire as shown.

6.Use tacks or staples to permanently attach entrapment warning label to wall near door control, and manual release/safety reverse test label in a prominent location on inside of garage door.

DO NOT connect power and operate opener at this time, The trolley will travel to the full open position but will not return to the close position until the sensor beam is connected and properly aligned.

TopreventpossibleSERIOUSINJURYor DEATHfrom electrocution:

•Besurepoweris not connectedBEFOREinstallingdoor control.

•ConnectONLYto 24 VOLTlow voltagewires. TopreventpossibleSERIOUSINJURYor DEATHfroma closinggaragedoor:

•Installdoorcontrolwithinsightof garagedoor,out of reachof childrenat aminimumheightof 5feet,andaway fromall movingpartsof door.

•NEVERpermitchildrento operateor playwithdoorc0ntrol pushbuttonsor remotecontroltransmitters.

•ActivatedoorONLYwhenit canbeseenclearly,is properly adjusted,andthereareno obstructionsto doortravel.

ALWAYSkeepgaragedoor insight untilcompletelyclosed. NEVERpermitanyoneto crosspathof closinggaragedoor.

Outside Keylock Accessory Connections

To opener terminal screws: white to 2; white/red to 1

_] I_!ll_illlllliltltl Illliillllil_>	HARDWARE		SHOWN
		ACTUAL	SIZE
6AB x 1-1/2"Screw
Door Control Button
H; IAI212Il1111/12,,tiSIcl'el/VJ_	_	nsulated
Control Console (std installation)		Staples
I 116!; I21IxII ,! ':Ictrle!; II
Control Console (pre-wired)	Dry	Wall Anchors

Figure 1		Figure 2
REMOVE & REPLACE	COVER	PRE-WtRED
TO Replace,	To Remove,	INSTALLATION
Insert Top	Twist
Tabs._. First.	Here	24 Volt
		2-Conductor
		Bell Wire in
		Gang Box
Lighted
Push Button

			:_F==_===_==	Top
			_v	Mounting
				- Hole
		/	.	> Terminal
			_	Sorews
Screws	Bell			Bottom
	Wire
Terminal		Ben		Mounting
		Wire	_	Hole
(BACK V_EW)			(BACK VIEW)
	DOOR CONTROL BUTTON		PREMIUM	CONTROL CONSOLE

Back Panel

of Opener

18