Manuals / Sears / Fitness & Sports / Home Gym

Sears 831.159460 High Pulley, Other Side, Butterfly, Lifestyler System, Vertical Knee Raise

Models: 831.159460

1 28

Page 17

38.Remove the decals from the decal sheet (not shown) and apply them to the home gym system in the loca- tions shown in the illustration below.

38
HIGH PULLEY
(OTHER SIDE)
	BUTTERFLY
	LIFESTYLER SYSTEM 200
VERTICAL KNEE RAISE	BENCH PRESS
	BENCH PRESS
	PREACHER CURL
	LEG EXTENSION
	LOW PULLEY

39.Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENT, beginning on page 18 of this manual.

Before using the home gym system, pull each cable a few times to be sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If the cables are not properly installed, they may be damaged when heavy weight is used. See the CABLE DIAGRAM on page 22 of this manual for proper cable routing. If there is any slack in the cables, you will need to remove it by tightening the cables. See TROUBLE-SHOOTING AND MAINTE- NANCE on page 21.

Page 17

Image 17

Sears 831.159460 High Pulley, Other Side, Butterfly, Lifestyler System, Vertical Knee Raise, Bench Press, Preacher Curl

Contents

USERS MANUAL Model No Serial NoPATENT PENDING SEARS, ROEBUCK AND CO., DEPT. 817WA, HOFFMAN ESTATES, IL TABLE OF CONTENTSFULL 90 DAY WARRANTY 9. Always wear athletic shoes for foot protection IMPORTANT PRECAUTIONS8. Keep hands and feet away from moving parts BEFORE YOU BEGIN FRAME ASSEMBLY ASSEMBLYTHE FOLLOWING TOOLS NOT INCLUDED ARE REQUIRED FOR ASSEMBLY Two 2 adjustable wrenches One 1 standard screwdriverLocknuts yet Carriage Bolt. Do not tighten the NylonTighten all Nylon Locknuts used in steps 1 through FRAME ASSEMBLYBushings should fit on each end of the 4. Note This will be a tight fit. The Plasticindicated tube in the Base. Be sure that the 3 1/2” Pulleys 15 are on the indicatedARM ASSEMBLY Long Cable Trap is positioned to hold the Cable in place CABLE ASSEMBLY20 can move freely 17. See the inset drawing. Attach a 3 1/2” Pulley CABLE ASSEMBLYCABLE ASSEMBLY from other side Inset shows viewInset shows view from other side CABLE ASSEMBLYnot completely tighten the Nylon Locknut CABLE ASSEMBLY SEAT ASSEMBLYIt should be threaded onto the end of the Cable so only a couple of threads areSEAT ASSEMBLY SEAT ASSEMBLY Cable 35 and the Curl Bar 86 as shownSquare Inner Caps may come pre-assem- bled VKR ASSEMBLY OTHER SIDE HIGH PULLEYBUTTERFLY LIFESTYLER SYSTEMCHANGING THE WEIGHT SETTING ADJUSTMENTATTACHING THE LAT BAR OR NYLON STRAP TO THE HIGH PULLEY STATION ATTACHING THE LAT BAR OR NYLON STRAP TO THE LOW PULLEY STATIONATTACHING AND REMOVING THE SEAT USING THE CURL BARATTACHING THE LEG LEVER TO THE LOW PULLEY STATION ATTACHING AND REMOVING THE CURL FRAMEWEIGHT RESISTANCE CHART ADJUSTING THE SHORT CABLEPRESS ARM BUTTERFLY ARMTIGHTENING THE CABLES TROUBLE-SHOOTING AND MAINTENANCELong Cable TOP VIEW CABLE DIAGRAMMedium Cable Short Cable1/2 x 1/2 Bushing 5/8 x 9/16 Spacer1/2 x 3/4 Spacer 1/2 x 3/8 Spacer 1 x 7/8 Plastic Bushing 1 Square Inner Cap1/4 x 2 Screw 1/4 Nylon Locknut5/16 Nylon Locknut3-23 1/4 x 2 Carriage Bolt1 1/4 x 2 1/2 Plastic Bushing 3/8 x 3 1/2 Bolt 3/8 x 3 3/4 Bolt 5/16 x 5 Bolt 5/16 x 6 BoltCable Clip 1 RetainerR0696A PART LIST-Model NoPart DescriptionEXPLODED EXPLODED DRAWING-Model NoR0995A 3738Model No a part is missing or you need to schedule repair serviceIf you find that you need help assembling or operating the LIFESTYLER SYSTEM

HIGH PULLEY

(OTHER SIDE)

BUTTERFLY

LIFESTYLER SYSTEM 200

VERTICAL KNEE RAISE

BENCH PRESS

PREACHER CURL

LEG EXTENSION

LOW PULLEY