ASSEMBLY
ASSEMBLY
CASTER WHEEL ATTACHMENTS
WING MOWER (FIGURE 9)
Attach the inside (1) and outside |
|
|
|
|
|
Axle Arm Weldments (1 or 1A) to the |
|
|
|
|
|
outer deck with 3/8" Gr. 2 bolt (2), |
|
|
|
|
|
flatwasher |
|
|
| 1 | 1A |
(3), and 3/8" locknut (4) installed in |
| 8 |
|
| 4 |
outer front hole. All other arm retain- |
|
|
| ||
ing bolts are Gr. 5, 3/8" bolts (5). See |
| 7 |
|
| 3 |
Fig. 13 & 14 for more details. Install |
|
|
|
|
|
spacer (7,8,9) and forks as describe |
|
|
|
|
|
in rear mower (Figure 8). The inside |
|
|
|
|
|
rear leg of the wing mowers will | 7 |
|
|
|
|
require a height adjustment shaft |
| 4 | 3 |
| |
|
|
| |||
(11), spacer tube (12) and a spacer | 11 |
| 2 | ||
pad (13) installed with a 3/8" x 1 1/2" |
|
|
| ||
12 |
|
|
|
| |
socket head screw (14). |
|
|
|
| |
| 13 | 1 | 5 |
| FIGURE 9 |
|
| 10 | |||
NOTE: Spacer (13) rests on support |
|
|
| ||
|
|
|
| ||
| 14 |
|
|
| |
flat welded to frontside of mainframe |
|
| 7,8,9 |
|
cross tube. |
|
|
|
|
|
| 10 |
|
|
|
| 8 |
|
|
| 6 | 7 |
|
|
CASTER WHEEL ATTACHMENTS |
|
| 4 | |
|
|
| ||
REAR MOWER (11' MODEL) |
|
|
| |
|
|
| 10 | |
FIGURE 10 | 7 |
| 3 | |
| 5 |
| 8 | |
Attach the right and left Axle Arm |
|
| ||
|
|
|
| |
Weldment (1) to the deck with 3/8" |
|
|
|
|
Gr. 5 bolts (2) flatwasher |
|
|
| 7 |
x 3/16" thick) (3), and 3/8" locknuts |
| 1 |
|
|
(4). NOTE: Mount the inside and |
| 2 | 5 | |
|
| |||
outside rear arms in the forward set |
|
|
| |
|
|
|
| |
of holes. Install four one inch spac- |
|
|
| 6 |
ers (7) and two 1/4 inch spacer (8) |
|
|
| 7 |
on each fork and wheel assembly |
|
|
|
|
(9). Insert Wheel assembly Shaft |
|
|
| 9 |
(9) into Axle Arm Weldment (1) and |
|
|
| |
|
|
|
| |
retain with Snapper Pin (10). |
|
|
|
|
NOTE: Front Fork and Wheel As- | 1 |
|
|
|
semblies have Lock mechanism |
|
|
|
|
which will not allow wheel to caster |
|
|
|
|
360 degrees. See page | FIGURE 10 |
|
|
|
Deck detail. |
|
|
|
|
Turf Flex 08/01 | Assembly Section |
|
| R |
|
|
|
© 2004 Alamo Group Inc.