Sharp DV-RW370X operation manual Functional overview cont’d, Rear Panel, Remote Control

Before you start

Functional overview (cont’d)

Rear Panel

DVD/VCR		DVD
AV2 (DECODER)	DIGITAL	AUDIO	S-VIDEO	COMPONENT
	AUDIO OUT	OUT	OUT	VIDEO OUT
				Y
		L		PB
	OPTICAL COAXIAL			/CB
AV1 (TV)
		R		PR
				/CR

1 2 3 4 5 67 8

ANTENNA
IN
OUT
9	10

1Mains cable

• Connect to a standard AC outlet.

2AV1 (TV) Scart terminal (VCR / DVD)

•Connect to the Scart terminal on your TV.

Use the supplied Scart output adaptor with the Video / Audio cables if your TV has no Scart terminal.

3AV2 (DECODER) Scart terminal (VCR / DVD)

•Connect to the Scart terminal of VCR, camcorder, or other Audio-Video equipment. Use a commercially available Scart cable.

4DIGITAL AUDIO OUT (OPTICAL) jack (DVD)

•Connect to an amplifier with a digital input jack such as a Dolby Digital decoder, DTS decoder or MPEG decoder.

Use a commercially available Optical cable.

5DIGITAL AUDIO OUT (COAXIAL) jack (DVD)

•Connect to an amplifier with a digital input jack such as a Dolby Digital decoder, DTS decoder or MPEG decoder.

Use a commercially available Coaxial cable.

Note

6AUDIO OUT (ANALOG) jacks (DVD)

•Connect to the audio input jacks on your TV. Use a commercially available Audio cable.

7S-VIDEO OUT jack (DVD)

•Connect to the S-Video input jack on your TV. Use a commercially available S-Video cable.

8COMPONENT VIDEO OUT jacks (DVD)

•Connect to the component video input jacks on your TV.

Use a commercially available Component video cable.

9ANTENNA OUT jack (VCR / DVD)

•Connect to the Aerial jack on your TV, cable box or direct broadcast system.

Use the supplied Round Coaxial cable.

10ANTENNA IN jack (VCR / DVD)

• Connect to an antenna or cable.

•Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the unit.

•This unit does not have an RF modulator.

	*	…You can also turn on the unit by pressing these buttons
Remote Control
		when the remote control is in DVD mode.

1					33
	OPERATE		SETUP	OPEN/CLOSE
2		DUBBING		EJECT	32*
3	T-SET	TIMER PROG. REC MODE RAPID PLAY			31
4					30
5	ZOOM	VCR	DVD	CM SKIP	29
6	TOP MENU			MENU LIST	28
7					27
8	RETURN			ENTER	26
9
	.@/:	ABC	DEF
	1	2	3	PROG.	25
	GHI	JKL	MNO
10
	4	5	6
	PQRS	TUV	WXYZ

1DUBBING button (VCR / DVD)

•Press to start VCR to DVD (DVD to VCR) duplication which you set in the Setup menu.

2 OPERATE button (VCR / DVD)

•Press to turn on or off the unit.

•If timer programming is set, press to switch the unit to the timer-standby mode.

3TIMER PROG. button (VCR / DVD)

• Press to display the timer programme setting menu.

4T-SET button (VCR / DVD)

•Press to enter the timer-standby mode. In the timer- standby mode, press to cancel the mode and to turn on the unit.

		7	8	9	SKIP	24
		CLEAR/C-RESET	SPACE	DISPLAY
11
			0		23
12*		REV
					FWD
13				PLAY		22
		VCR			DVD
		REC/OTR			REC/OTR
14	15			STOP		21
16		REPEAT	AUDIO	SEARCH	SLOW	20
	17				19
					PAUSE	18

5ZOOM button (DVD)

•During playback, press to enlarge the picture on the screen.

6VCR button

•Press to activate the remote control in VCR mode. (See page 11.)

•Press to select the VCR output mode.

7TOP MENU button (DVD)

• Press to display the Title menu.

8Cursor K / L/ s/ B buttons (VCR / DVD)

• Press to select items or settings.

8EN