Quick guide

Initial auto installation

When the TV is powered on for the first time after purchase,
the initial auto installation wizard appears. Follow the menus
and make the necessary settings one after another.
Press a on the TV.
The initial auto installation wizard appears.
Setting the OSD language.
English
Italiano
Svenska
Press a/b/c/d to select the desired language, and
then press OK.
Selecting the location of the TV.
STOREHOME
Press c/d to select where you will use this TV, and
then press OK.
HOME: “STANDARD” will be the default value for the “AV
MODE” setting.
STORE: “DYNAMIC (Fixed)” will be the default value for the
“AV MODE” setting. If the “AV MODE” is changed, the TV will
automatically switch back to “DYNAMIC (Fixed)” when there
is no signal input from the TV or remote control unit for 30
minutes.
A demonstration image will be displayed after initial auto
installation is completed. If you have chosen “STORE” by
mistake, go to “Setup” > “Reset” > select “HOME” again.
Setting the country.
Austria A B/G
Finland
FIN
B/G
Greece GR B/G
Press a/b/c/d to select your country or area, and
then press OK.
This setting screen only appears during the first installation.
Starting channel search.
Analogue SearchDigital Search
Press c/d to select “Digital Search” or “Analogue
Search”, and then press OK.
If you want to search for more broadcasts, execute
“Additional Search” from the “Programme Setup” menu
(Pages 26 and 27).
To watch both analogue broadcasts and digital broadcasts,
you should perform the channel search setting for each
format.
EXAMPLE
If you execute “Digital Search” in the initial auto installation
wizard, you should perform “Analogue Search” from “Auto
Installation” under the “Setup” menu (Pages 26 and 27).
1
•
2
3
•
•
•
4
•

5

•
•
•
The TV searches for, sorts and stores all the
receivable TV stations according to their settings
and the connected antenna.
To abort the initial auto installation in progress, press 6.
NOTE
If you turn off the power on the TV after performing step 5, the
initial auto installation wizard does not appear. The auto installation
function allows you to execute the installation again from the
“Setup” menu (Page 26).
The initial auto installation wizard will go off if you leave the TV
unattended for 30 minutes before searching for channels in step 6.
After initial auto installation is completed, the default PIN is
automatically set to “1234”. To change the PIN setting, refer to
Password/Parental lock settings on page 28. To clear the PIN
setting (PIN input will no longer be needed), refer to CLEARING
THE PIN on page 40.
When “Italy” is selected in the country setting, the default PIN is
automatically set to “1234” and the default age restriction value is
set to 18.

Checking signal strength and

channel strength

If you install a DVB-T antenna for the first time or
relocate it, you should adjust the alignment of the
antenna to receive a good reception while checking
the antenna setup screen.
Press MENU and the “MENU” screen displays.
Press c/d to select “Setup”.
Press a/b to select “Antenna Setup-DIGITAL”,
and then press OK.
Checking signal strength
Press a/b to select “Signal Strength”.
Signal Strength
Supply Voltage
Channel Strength
Signal Strength
Quality
Current Max 0
CH No. 21
0
Current Max 0 0
Checking channel strength
Press a/b to select “Channel Strength”, and
then press OK.
You can input a specified frequency band using the 0–9
numeric buttons.
Signal Strength
Supply Voltage
Channel Strength
Signal Strength
Quality
Current Max0
CH No. 21
0
Current Max00

474.0MHz

Position and align the antenna so that the
maximum possible values for “Signal Strength”
and “Quality” are obtained.
NOTE
The values of “Signal Strength” and “Quality” indicate when to
check the appropriate alignment of the antenna.

6

•
•
•
•
•
1
2
3
E
E
•
4
•
9

Confirm the following before turning

on the power

Is the antenna cable connected?
Is the AC cord plugged in?
E
E