Installing the Lithium, Memory Battery | Sharp VL AH 50 H guide

	Installing the Lithium	5 Close the cassette compartment door by
	Memory Battery	pressing the centre until it clicks into
	Memory Battery	place.
		place.

The supplied lithium battery is used to store the memory of the date and time settings.

1 Slide the cassette compartment door release and open the cassette compartment door.

	Cassette compartment
	door release	Removing the Lithium Battery
		Perform steps 1 and 2 above, then lift out the
		battery from the battery holder.
		Note:
		• Replace the battery with a new CR2025 battery
		when the date and time indicator starts to fall
		behind the correct time.
	Note: The cassette holder will extend and	Notes on the Use of the Lithium
	open when the VIEWCAM is connected to a	Battery
	power source. Be sure to close the cassette
	holder before proceeding to the next step	CAUTION: Danger of explosion if battery is
	(see page 11).	CAUTION: Danger of explosion if battery is
	(see page 11).	incorrectly replaced. Replace only with the
		incorrectly replaced. Replace only with the
	2 Pull out the lithium battery holder using	same or equivalent type CR2025 recommended
	2 Pull out the lithium battery holder using	by the equipment manufacturer.
	a pointed object such as the tip of a	WARNING KEEP THIS BATTERY AWAY FROM
	ballpoint pen.	WARNING KEEP THIS BATTERY AWAY FROM
	ballpoint pen.	CHILDREN. IF SWALLOWED, CONSULT A
		PHYSICIAN IMMEDIATELY FOR EMERGENCY
		TREATMENT.
		CAUTION BATTERY MAY EXPLODE IF MIS-
		USED OR INSTALLED WITH POLARITY
		REVERSED. DO NOT RECHARGE, DISAS-
		SEMBLE OR DISPOSE OF IN FIRE.

Preparation

Lithium battery holder

3 Insert the lithium battery into the battery holder with the ` side of the battery facing the j side of the holder.

j mark

4 Push the battery holder back into position.

•Do not short-circuit, recharge, disassemble, or heat the lithium battery.

•Should the lithium battery leak, wipe the battery compartment and holder clean, and then insert a new battery.

•The lithium battery will last about one year of normal usage.

12

Image 19

Sharp VL AH 50 H operation manual Installing the Lithium, Memory Battery, Removing the Lithium Battery

Contents

VL-AH50H Power supply Blue Neutral Brown Live Special Note for Users in the U.K Avoid shocks and dropping Do not aim the lens at the sunAvoid placing LCD Monitor Screen Recording Format Iii Battery packCR2025 type Audio/video cable Lithium battery Remote control × Soft case Tripod adapter For 180 recording Contents Gamma Brightness Compensation Useful FeaturesAdvanced Features References Cassette compartment door p When the cassette compartment door is openPart Names Operation Summary Remote sensor p Rear view 47 p 34 p Camera ModeVCR Mode On-screen Display Index Quick Reference Index Video cassette is defective and should be Inserting and Removing Battery PackInserting the Battery Pack Removing the Battery Pack Recording and playback times Charging the Battery Pack Powering the Viewcam from an AC Outlet Perform above, then take out the cassette Inserting and Removing a CassetteInserting a Cassette Removing a Cassette Removing the Lithium Battery Installing the LithiumMemory Battery Battery Changing to the 12-hour Time Mode Setting the Date and TimePress the SET button B LCD screen side Using the Hand Strap and the Lens CapAttaching the Shoulder Strap Attaching and Removing the Lens Cap Opening the Sun Hood Using the Sun HoodAttaching the Sun Hood Closing the Sun Hood Maximum Continuous Recording and Actual Recording Times Easy Camera Recording with Full Auto ModeTo Turn the Power Off To Pause Recording Tips on Recording Positions ZoomingBasic Operations Camera Recording Approx. remaining On-screen Recording time Indicator Remaining Battery Power DisplayRemaining Recording Time Display Auto Tape Rewind Volume ControlPlayback To Stop Playback Turn on the Viewcam in VCR mode, and begin tape playback see Watching the Playback on a Basic Operations Playback Video SearchStill Slow Operation buttons Operations of the On-screen ControlsMenu button Display button Perform steps 4 to 6 above Desired settingPress the SET button B to select Press the or button C or D to select the desired menu item Press the button to select Select Recording the Date and TimePress the or Button to select Press the SET button B to select AUTO, ON, or OFF To return to optical zoom Setting the Digital Zoom Digital Quick Zoom Extend Zoom Using Digital Quick ZoomSetting the Digital Quick Zoom Ranges To cancel Digital Quick Zoom Type of Still Recording Modes Selecting Still Recording ModeUsing Still Recording Still Recording Digital Image Stabilization DIS To cancel Strobe Recording modeTo return to normal recording mode Strobe Recording Fade In and Fade Out Selecting Fade ModeUsing Fade Mode Press the SET button B to select the desired fade mode Quick Review To cancel Fade modeTo use fade out only Recording Standby mode, press Menu button until appears Quick Return Edit Search Press the Gama EFF. button a again To cancel Gamma Brightness CompensationGamma Brightness Compensation To obtain a brighter picture Gain-up Cat’s Eye To cancel the gain-up function To return to normal picture Wide ScreenMacro Shots Removing the Lens Hood To pause recording, press the REC Stop button B Self RecordingNormal Self Recording More Information on Self Recording Self-recording Message Press the Message button in Recording Standby modeTo turn off the self-recording message screen Setting the Viewcam to Full Auto Mode Program Search FeaturesUseful To turn off the tape counter Tape Counter FeatureUsing the Counter To reset the counter to zero During playback, press the Menu Button until appears Using the Counter MemoryPress the Play button D to view the desired scene Turning On the Remote Control Mode Using the Remote ControlOperating the Remote Control Installing the Batteries in the Remote Control Type of Digital Picture Effects To cancel the digital picture effectAdvanced Features Digital Picture Effects Select Scene Menu in above Type of Scene SettingsTo cancel the scene setting Scene Menu Program AE Superimposing a Title Top of the screen and the cursor will Changing the Preset TitlesPress the Reset button to display the title input screen Press the or ß button Q to select Manual Focus To cancel Manual Focus modeAuto/Manual Focus Auto Focus White Balance Lock To cancel White Balance LockPress the White BAL. button. White BAL. returns to blue Manual Exposure To cancel Manual Exposure modePerform steps 1 and 2 above, then press the Auto button B Selecting Digital Dual Picture Digital Dual PicturePicture-in-Picture Title Screen Type of Backlight Modes Picture/Backlight AdjustmentsPress the Menu button until Camera mode or VCR mode appears Press the Exit button to turn off the adjustment screen Press the Gama EFF. button again. Gamma disappears To cancel Gamma PlaybackGamma Playback Turning Off the LCD Monitor Backlight To stop editing Setting Edit ModeEditing Cutting Unwanted Sequences Tips on Good Lighting Useful InformationHints for Better Shooting Lighting Dirty Video Heads Dew Formation Replacing the Fluorescent Lamp Battery Pack AC Adapter CleaningUsing Your Viewcam Abroad References Video Cassette Tapes Watching the Demonstration Demonstration ModeCancelling Demo Mode Button and slide Power switch to Power Camera mode Symptom Possible cause Suggested solution Before Requesting Service VCR Viewcam SpecificationsPage Page Page 0P06-M-G