Manuals / Sharp / Computer Equipment / Projector

Sharp XG-C335X, XG-C430X, XG-C330X Changing the Lens, Insert the lens into the projector

Models: XG-C330X XG-C335X XG-C430X

1 45

Download 45 pages 2.42 Kb

Page 10

Image 10

Changing the Lens

5 Insert the lens into the projector.

•As you insert the lens, look inside the window to make sure that the pin is in- serted into the hole of the lens mount.

Lens mount

Slide the lens fastener catch tab in the direction of “LOCK” until it stops.

•Be careful not to rotate the lens fastener ring too tight, as the lens fastener ring will be difficult to loosen the next time the lens is changed.

Replace the lens housing cover.

•If the lens housing cover is not secured to the projector, you will not be able to turn the power on.

Lens fastener catch tab

-10

Page 10

Image 10

Sharp XG-C335X, XG-C430X, XG-C330X Changing the Lens, Insert the lens into the projector, Replace the lens housing cover

Contents

LCD PROJECTOR SETUP MANUALXG-C430X XG-C335X XG-C330X MODELSide View Setting up the ScreenStandard Setup Front Projection Example of standard setupThrow Distance The graph below is for 100 inches 254 cm screen with 43 normal modeScreen Size and Projection Distance ScreenF1.7-F1.9, f=28.0-33.6 mm Standard Zoom LensScreen Size and Projection Distance NORMAL ModeNORMAL Mode Wide-zoom Lens AN-C12MZF2.2-F2.7, f=24.5-30.7 mm STRETCH ModeNORMAL Mode Tele-zoom Lens AN-C18MZF1.7-F2.2, f=36.5-46.3 mm STRETCH ModeNORMAL Mode Tele-zoom Lens AN-C27MZF2.0-F2.8, f=53.8-82.9 mm STRETCH ModeNORMAL Mode Tele-zoom Lens AN-C41MZF2.1-F2.8, f=83.5-117.2 mm STRETCH ModeRemove the lens by pulling it straight out Changing the LensRemove the protection cap from the back of the new lens Changing the Lens Replace the lens housing cover5 Insert the lens into the projector Signal Connecting Pin AssignmentsRS-232C Cable recommended connection 9-pin D-sub female connector SignalPin No. Signal Connecting Pin AssignmentsDVI-D Input Terminal Pin No. SignalCommunication conditions RS-232C Specifications and CommandsComputer control Basic formatExample When turning on the projector, make the following setting CommandsRS-232C Specifications and Commands P O W RRS-232C Specifications and Commands PARAMETERRS-232C Specifications and Commands PJLinkTM Compliant RS-232C Specifications and Commands5 Lamp Timer Reset command is available only in standby mode For additional information, visit “http//pjlink.jbmia.or.jp/english/”1. Connecting the projector to a computer Setting up the Projector Network EnvironmentNetwork settings on the computer 2. Setting an IP address for the computer3 Plug the power cord into the AC socket of the projector 1. Connecting the Pro- jector to a ComputerSetting up the Projector Network Environment 4 Turn on the computerRight-click “Local Area Connec 2. Setting an IP Address for the Computer2 Click “Start”, and click “Control Panel” tion” and select “Properties”jector” Setting up the Projector Network Environment1 Start Internet Explorer version 3. Setting up a Network Connection for the ProjectorSetting up the Projector Network Environment Click the “Apply” button Setting up the Projector Network EnvironmentVersion 5.0 or later Controlling the Projector Using Internet ExplorerControlling the Projector via LAN 1 Start Internet Explorer version 5.0 or later on the computerControlling the Projector via LAN Confirming the ProjectorControlling the Projector Status StatusProjector Settings & Adjustments Setting and Adjusting theSetting the Security Network - SecurityMail - Originator Settings Making General Settings for the Network NetworkSetting for Sending E-mail when an Error Occurs GeneralExample of the display when an error occurs Mail - Recipient SettingsOccurs Service & Support Access URL Controlling the Projector via LAN7 Input “setup” and press the “Enter” key Setting up the Projector Using RS-232C or TelnetWhen Connecting Using RS-232C “Password” is displayed. Input the password and press the“Enter”key6 Input “setup” and press the “Enter” key When Connecting Using TelnetSetting up the Projector Using RS-232C or Telnet 5 “Password” is displayed. Input the password and press the“Enter”keySetting up the Projector Using RS-232C or Telnet SETUP MENU Main MenuADVANCED SETUP MENU SETUP MENUSet Items View Setting Detail ListVView All Setting Setting up the Projector Using RS-232C or TelnetSSave & Quit Save Settings and QuitQuit without Saving Set tings QQuit UnchangedSubnet Mask Setting IP Address SettingDefault Gateway Setting User Name SettingDHCP Client Setting Password SettingProjector Name Setting 5PasswordEntering ADVANCED SETUP MENU Disconnecting All ConnecSetting Auto Logout Time Data Port SettingAccepting All IP Addresses Setting of Accept IP Ad- dressCarrying out Network Ping Test ADVANCED5Network Ping TestADVANCED!Restore Default Setting Setting of Search PortReturn to Default Settings Return to Main Menu2 Enter a name in the “Name”field, and click “OK” Resetting the Lamp Timer of the Projector via LANcode” field. From the “Connect using” drop-down menu, select 3 If you are required to enter the area code, enter it in the “AreaSend the lamp reset command “LPRE0001” Resetting the Lamp Timer of the Projector via LAN6 Click the “Settings” tab, and then click “ASCII Setup” 5 Click “Properties” on the “File” menuCheck the network settings for the computer and the projector TroubleshootingWhen connecting the projector using serial-connection For network settings for the projector, refer to pageC\ipconfig /? displays how to use “ipconfig.exe” TroubleshootingUsage examples of ipconfig C\ipconfigTroubleshooting Top View DimensionsUnits inches mm Side ViewWhen AN-C12MZ is installed Projector and Lens DimensionsDimensions When AN-C18MZ is installed