Manuals / Sharp / Computer Equipment / Projector

Sharp XG-C430X, XG-C335X, XG-C330X Changing the Lens, Remove the lens by pulling it straight out

Models: XG-C330X XG-C335X XG-C430X

1 45

Download 45 pages 2.42 Kb

Page 9

Image 9

Changing the Lens

Info

•Before changing the lens, turn off the power of the projector and remove the power cord from the wall outlet.

•Do not attempt to change the lens while the projector is mounted on the ceiling.

1 Remove the lens housing cover by using the supplied lens hous- ing cover removal tool to push down on the groove on the lens housing cover.

•Hold down the lens housing cover with your hand to prevent it from flying out.

2 Slide the lens fastener catch tab in the direction of “UNLOCK” while holding the lens to prevent it from falling out.

•Slide the lens fastener catch tab until the window located beside “LOCK” comes to the top. Look inside the window to make sure that the two grooves on the lens fas- tener ring are facing up.

Lens fastener catch tab

Two grooves

Window

Remove the lens by pulling it straight out.

Remove the protection cap from the back of the new lens.

-9

Page 9

Image 9

Sharp XG-C430X, XG-C335X, XG-C330X specifications Changing the Lens, Remove the lens by pulling it straight out

Contents

XG-C430X XG-C335X XG-C330X SETUP MANUALLCD PROJECTOR MODELStandard Setup Front Projection Setting up the ScreenSide View Example of standard setupScreen Size and Projection Distance The graph below is for 100 inches 254 cm screen with 43 normal modeThrow Distance ScreenScreen Size and Projection Distance Standard Zoom LensF1.7-F1.9, f=28.0-33.6 mm NORMAL ModeF2.2-F2.7, f=24.5-30.7 mm Wide-zoom Lens AN-C12MZNORMAL Mode STRETCH ModeF1.7-F2.2, f=36.5-46.3 mm Tele-zoom Lens AN-C18MZNORMAL Mode STRETCH ModeF2.0-F2.8, f=53.8-82.9 mm Tele-zoom Lens AN-C27MZNORMAL Mode STRETCH ModeF2.1-F2.8, f=83.5-117.2 mm Tele-zoom Lens AN-C41MZNORMAL Mode STRETCH ModeChanging the Lens Remove the lens by pulling it straight outRemove the protection cap from the back of the new lens Replace the lens housing cover Changing the Lens5 Insert the lens into the projector RS-232C Cable recommended connection 9-pin D-sub female connector Connecting Pin AssignmentsSignal SignalDVI-D Input Terminal Connecting Pin AssignmentsPin No. Signal Pin No. SignalComputer control RS-232C Specifications and CommandsCommunication conditions Basic formatRS-232C Specifications and Commands CommandsExample When turning on the projector, make the following setting P O W RPARAMETER RS-232C Specifications and CommandsRS-232C Specifications and Commands 5 Lamp Timer Reset command is available only in standby mode RS-232C Specifications and CommandsPJLinkTM Compliant For additional information, visit “http//pjlink.jbmia.or.jp/english/”Network settings on the computer Setting up the Projector Network Environment1. Connecting the projector to a computer 2. Setting an IP address for the computerSetting up the Projector Network Environment 1. Connecting the Pro- jector to a Computer3 Plug the power cord into the AC socket of the projector 4 Turn on the computer2 Click “Start”, and click “Control Panel” 2. Setting an IP Address for the ComputerRight-click “Local Area Connec tion” and select “Properties”Setting up the Projector Network Environment jector”3. Setting up a Network Connection for the Projector 1 Start Internet Explorer versionSetting up the Projector Network Environment Setting up the Projector Network Environment Click the “Apply” buttonControlling the Projector via LAN Controlling the Projector Using Internet ExplorerVersion 5.0 or later 1 Start Internet Explorer version 5.0 or later on the computerControlling the Projector Confirming the ProjectorControlling the Projector via LAN Status StatusSetting the Security Setting and Adjusting theProjector Settings & Adjustments Network - SecuritySetting for Sending E-mail when an Error Occurs Making General Settings for the Network NetworkMail - Originator Settings GeneralOccurs Service & Support Access URL Mail - Recipient SettingsExample of the display when an error occurs Controlling the Projector via LANWhen Connecting Using RS-232C Setting up the Projector Using RS-232C or Telnet7 Input “setup” and press the “Enter” key “Password” is displayed. Input the password and press the“Enter”keySetting up the Projector Using RS-232C or Telnet When Connecting Using Telnet6 Input “setup” and press the “Enter” key 5 “Password” is displayed. Input the password and press the“Enter”keyADVANCED SETUP MENU SETUP MENU Main MenuSetting up the Projector Using RS-232C or Telnet SETUP MENUVView All Setting View Setting Detail ListSet Items Setting up the Projector Using RS-232C or TelnetQuit without Saving Set Save Settings and QuitSSave & Quit tings QQuit UnchangedDefault Gateway Setting IP Address SettingSubnet Mask Setting User Name SettingProjector Name Setting Password SettingDHCP Client Setting 5PasswordSetting Auto Logout Time Disconnecting All ConnecEntering ADVANCED SETUP MENU Data Port SettingCarrying out Network Ping Test Setting of Accept IP Ad- dressAccepting All IP Addresses ADVANCED5Network Ping TestReturn to Default Settings Setting of Search PortADVANCED!Restore Default Setting Return to Main Menucode” field. From the “Connect using” drop-down menu, select Resetting the Lamp Timer of the Projector via LAN2 Enter a name in the “Name”field, and click “OK” 3 If you are required to enter the area code, enter it in the “Area6 Click the “Settings” tab, and then click “ASCII Setup” Resetting the Lamp Timer of the Projector via LANSend the lamp reset command “LPRE0001” 5 Click “Properties” on the “File” menuWhen connecting the projector using serial-connection TroubleshootingCheck the network settings for the computer and the projector For network settings for the projector, refer to pageUsage examples of ipconfig TroubleshootingC\ipconfig /? displays how to use “ipconfig.exe” C\ipconfigTroubleshooting Units inches mm DimensionsTop View Side ViewDimensions Projector and Lens DimensionsWhen AN-C12MZ is installed When AN-C18MZ is installed