Manuals / Sharp / Computer Equipment / Projector

Sharp XG-C335X, XG-C430X Connecting the Pro- jector to a Computer, Turn on the computer, Info

Models: XG-C330X XG-C335X XG-C430X

1 45

Download 45 pages 2.42 Kb

Page 19

Setting up the Projector Network Environment

Setting up the Projector Network Environment

1.Connecting the Pro- jector to a Computer

Establishing a one-to-one connection from the projector to a computer. Using a LAN cable (Category 5, cross-over type) you can config- ure the projector via the computer.

1 Disconnect the computer’s LAN cable from the existing network.

A LAN cable being connected to the network

2 Connect a LAN cable (a UTP cable, Category 5, cross-over type) to the projector’s LAN ter- minal and connect the other end of the cable to the computer’s LAN terminal.

LAN cable

(cross-over type, commercially available)

3 Plug the power cord into the AC socket of the projector.

4 Turn on the computer.

ON

Info

Confirm that the LINK LED on the rear of the projector illuminates. If the LINK LED does not illuminate, check the following :

•The LAN cable is properly connected.

•The power switches of both the projector and the computer are on.

This completes the connection. Now proceed to “2. Setting an IP Address for the Com- puter”.

-19

Image 19

Sharp XG-C335X, XG-C430X Connecting the Pro- jector to a Computer, Setting up the Projector Network Environment, Info

Contents

MODEL SETUP MANUALXG-C430X XG-C335X XG-C330X LCD PROJECTORExample of standard setup Setting up the ScreenStandard Setup Front Projection Side ViewScreen The graph below is for 100 inches 254 cm screen with 43 normal modeScreen Size and Projection Distance Throw DistanceNORMAL Mode Standard Zoom LensScreen Size and Projection Distance F1.7-F1.9, f=28.0-33.6 mmSTRETCH Mode Wide-zoom Lens AN-C12MZF2.2-F2.7, f=24.5-30.7 mm NORMAL ModeSTRETCH Mode Tele-zoom Lens AN-C18MZF1.7-F2.2, f=36.5-46.3 mm NORMAL ModeSTRETCH Mode Tele-zoom Lens AN-C27MZF2.0-F2.8, f=53.8-82.9 mm NORMAL ModeSTRETCH Mode Tele-zoom Lens AN-C41MZF2.1-F2.8, f=83.5-117.2 mm NORMAL ModeRemove the lens by pulling it straight out Changing the LensRemove the protection cap from the back of the new lens Changing the Lens Replace the lens housing cover5 Insert the lens into the projector Signal Connecting Pin AssignmentsRS-232C Cable recommended connection 9-pin D-sub female connector SignalPin No. Signal Connecting Pin AssignmentsDVI-D Input Terminal Pin No. SignalBasic format RS-232C Specifications and CommandsComputer control Communication conditionsP O W R CommandsRS-232C Specifications and Commands Example When turning on the projector, make the following settingPARAMETER RS-232C Specifications and CommandsRS-232C Specifications and Commands For additional information, visit “http//pjlink.jbmia.or.jp/english/” RS-232C Specifications and Commands5 Lamp Timer Reset command is available only in standby mode PJLinkTM Compliant2. Setting an IP address for the computer Setting up the Projector Network EnvironmentNetwork settings on the computer 1. Connecting the projector to a computer4 Turn on the computer 1. Connecting the Pro- jector to a ComputerSetting up the Projector Network Environment 3 Plug the power cord into the AC socket of the projectortion” and select “Properties” 2. Setting an IP Address for the Computer2 Click “Start”, and click “Control Panel” Right-click “Local Area ConnecSetting up the Projector Network Environment jector”1 Start Internet Explorer version 3. Setting up a Network Connection for the ProjectorSetting up the Projector Network Environment Setting up the Projector Network Environment Click the “Apply” button1 Start Internet Explorer version 5.0 or later on the computer Controlling the Projector Using Internet ExplorerControlling the Projector via LAN Version 5.0 or laterStatus Status Confirming the ProjectorControlling the Projector Controlling the Projector via LANNetwork - Security Setting and Adjusting theSetting the Security Projector Settings & AdjustmentsGeneral Making General Settings for the Network NetworkSetting for Sending E-mail when an Error Occurs Mail - Originator SettingsControlling the Projector via LAN Mail - Recipient SettingsOccurs Service & Support Access URL Example of the display when an error occurs“Password” is displayed. Input the password and press the“Enter”key Setting up the Projector Using RS-232C or TelnetWhen Connecting Using RS-232C 7 Input “setup” and press the “Enter” key5 “Password” is displayed. Input the password and press the“Enter”key When Connecting Using TelnetSetting up the Projector Using RS-232C or Telnet 6 Input “setup” and press the “Enter” keySETUP MENU SETUP MENU Main MenuADVANCED SETUP MENU Setting up the Projector Using RS-232C or TelnetSetting up the Projector Using RS-232C or Telnet View Setting Detail ListVView All Setting Set Itemstings QQuit Unchanged Save Settings and QuitQuit without Saving Set SSave & QuitUser Name Setting IP Address SettingDefault Gateway Setting Subnet Mask Setting5Password Password SettingProjector Name Setting DHCP Client SettingData Port Setting Disconnecting All ConnecSetting Auto Logout Time Entering ADVANCED SETUP MENUADVANCED5Network Ping Test Setting of Accept IP Ad- dressCarrying out Network Ping Test Accepting All IP AddressesReturn to Main Menu Setting of Search PortReturn to Default Settings ADVANCED!Restore Default Setting3 If you are required to enter the area code, enter it in the “Area Resetting the Lamp Timer of the Projector via LANcode” field. From the “Connect using” drop-down menu, select 2 Enter a name in the “Name”field, and click “OK”5 Click “Properties” on the “File” menu Resetting the Lamp Timer of the Projector via LAN6 Click the “Settings” tab, and then click “ASCII Setup” Send the lamp reset command “LPRE0001”For network settings for the projector, refer to page TroubleshootingWhen connecting the projector using serial-connection Check the network settings for the computer and the projectorC\ipconfig TroubleshootingUsage examples of ipconfig C\ipconfig /? displays how to use “ipconfig.exe”Troubleshooting Side View DimensionsUnits inches mm Top ViewWhen AN-C18MZ is installed Projector and Lens DimensionsDimensions When AN-C12MZ is installed