Manuals / Sharp / Computer Equipment / Projector

Sharp XG-C335X, XG-C430X Resetting the Lamp Timer of the Projector via LAN, Close HyperTerminal

Models: XG-C330X XG-C335X XG-C430X

1 45

Download 45 pages 2.42 Kb

Page 40

Image 40

Resetting the Lamp Timer of the Projector via LAN

5 Click “Properties” on the “File” menu.

6 Click the “Settings” tab, and then click “ASCII Setup”.

7 Select the check boxes next to “Send line ends with line feeds”, “Echo typed characters locally”, and “Append line feeds to in- coming line ends”, and click “OK”.

•The LAMPRESET Properties window

appears, click “OK”.

8 If a user name and/or password is set for the projector, enter the user name and password.

Send the lamp reset command “LPRE0001”.

•This command can only be sent when the projector is in standby mode.

•When “OK” is received, this indicates that the lamp was successfully reset.

10 Close HyperTerminal.

-40

Page 40

Image 40

Sharp XG-C335X, XG-C430X, XG-C330X Resetting the Lamp Timer of the Projector via LAN, Click “Properties” on the “File” menu

Contents

SETUP MANUAL XG-C430X XG-C335X XG-C330XLCD PROJECTOR MODELSetting up the Screen Standard Setup Front ProjectionSide View Example of standard setupThe graph below is for 100 inches 254 cm screen with 43 normal mode Screen Size and Projection DistanceThrow Distance ScreenStandard Zoom Lens Screen Size and Projection DistanceF1.7-F1.9, f=28.0-33.6 mm NORMAL ModeWide-zoom Lens AN-C12MZ F2.2-F2.7, f=24.5-30.7 mmNORMAL Mode STRETCH ModeTele-zoom Lens AN-C18MZ F1.7-F2.2, f=36.5-46.3 mmNORMAL Mode STRETCH ModeTele-zoom Lens AN-C27MZ F2.0-F2.8, f=53.8-82.9 mmNORMAL Mode STRETCH ModeTele-zoom Lens AN-C41MZ F2.1-F2.8, f=83.5-117.2 mmNORMAL Mode STRETCH ModeRemove the lens by pulling it straight out Changing the LensRemove the protection cap from the back of the new lens Changing the Lens Replace the lens housing cover5 Insert the lens into the projector Connecting Pin Assignments RS-232C Cable recommended connection 9-pin D-sub female connectorSignal SignalConnecting Pin Assignments DVI-D Input TerminalPin No. Signal Pin No. SignalRS-232C Specifications and Commands Computer controlCommunication conditions Basic formatCommands RS-232C Specifications and CommandsExample When turning on the projector, make the following setting P O W RRS-232C Specifications and Commands PARAMETERRS-232C Specifications and Commands RS-232C Specifications and Commands 5 Lamp Timer Reset command is available only in standby modePJLinkTM Compliant For additional information, visit “http//pjlink.jbmia.or.jp/english/”Setting up the Projector Network Environment Network settings on the computer1. Connecting the projector to a computer 2. Setting an IP address for the computer1. Connecting the Pro- jector to a Computer Setting up the Projector Network Environment3 Plug the power cord into the AC socket of the projector 4 Turn on the computer2. Setting an IP Address for the Computer 2 Click “Start”, and click “Control Panel”Right-click “Local Area Connec tion” and select “Properties”jector” Setting up the Projector Network Environment1 Start Internet Explorer version 3. Setting up a Network Connection for the ProjectorSetting up the Projector Network Environment Click the “Apply” button Setting up the Projector Network EnvironmentControlling the Projector Using Internet Explorer Controlling the Projector via LANVersion 5.0 or later 1 Start Internet Explorer version 5.0 or later on the computerConfirming the Projector Controlling the ProjectorControlling the Projector via LAN Status StatusSetting and Adjusting the Setting the SecurityProjector Settings & Adjustments Network - SecurityMaking General Settings for the Network Network Setting for Sending E-mail when an Error OccursMail - Originator Settings GeneralMail - Recipient Settings Occurs Service & Support Access URLExample of the display when an error occurs Controlling the Projector via LANSetting up the Projector Using RS-232C or Telnet When Connecting Using RS-232C7 Input “setup” and press the “Enter” key “Password” is displayed. Input the password and press the“Enter”keyWhen Connecting Using Telnet Setting up the Projector Using RS-232C or Telnet6 Input “setup” and press the “Enter” key 5 “Password” is displayed. Input the password and press the“Enter”keySETUP MENU Main Menu ADVANCED SETUP MENUSetting up the Projector Using RS-232C or Telnet SETUP MENUView Setting Detail List VView All SettingSet Items Setting up the Projector Using RS-232C or TelnetSave Settings and Quit Quit without Saving SetSSave & Quit tings QQuit UnchangedIP Address Setting Default Gateway SettingSubnet Mask Setting User Name SettingPassword Setting Projector Name SettingDHCP Client Setting 5PasswordDisconnecting All Connec Setting Auto Logout TimeEntering ADVANCED SETUP MENU Data Port SettingSetting of Accept IP Ad- dress Carrying out Network Ping TestAccepting All IP Addresses ADVANCED5Network Ping TestSetting of Search Port Return to Default SettingsADVANCED!Restore Default Setting Return to Main MenuResetting the Lamp Timer of the Projector via LAN code” field. From the “Connect using” drop-down menu, select2 Enter a name in the “Name”field, and click “OK” 3 If you are required to enter the area code, enter it in the “AreaResetting the Lamp Timer of the Projector via LAN 6 Click the “Settings” tab, and then click “ASCII Setup”Send the lamp reset command “LPRE0001” 5 Click “Properties” on the “File” menuTroubleshooting When connecting the projector using serial-connectionCheck the network settings for the computer and the projector For network settings for the projector, refer to pageTroubleshooting Usage examples of ipconfigC\ipconfig /? displays how to use “ipconfig.exe” C\ipconfigTroubleshooting Dimensions Units inches mmTop View Side ViewProjector and Lens Dimensions DimensionsWhen AN-C12MZ is installed When AN-C18MZ is installed