Manuals / Sharp / Computer Equipment / Projector

Sharp XG-C330X Setting up the Projector Using RS-232C or Telnet, When Connecting Using RS-232C

Models: XG-C330X XG-C335X XG-C430X

1 45

Download 45 pages 2.42 Kb

Page 29

Setting up the Projector Using RS-232C or Telnet

Setting up the Projector Using RS-232C or Telnet

Connect the projector to a computer using RS-232C or Telnet, and open the SETUP MENU on the computer to carry out various settings for the projector.

When Connecting Using RS-232C

1 Launch general purpose terminal emulator.

2 Input settings for the RS-232C port of the terminal emulator as follows.

Baud Rate	: 9600 bps*
Data Length	: 8 bit
Parity Bit	: None
Stop Bit	: 1 bit
Flow Control	: None

*This is the factory default setting. If the value of Baud Rate for the projector has been changed, set Baud Rate here according to the changed value on the projector.

7 Input “setup” and press the “Enter” key.

•SETUP MENU will be displayed.

▼SETUP MENU

---------------------------------	SETUP MENU--------------------------------
	SETUP MENU--------------------------------
[1]IP Address	[2]Subnet Mask	[3]Default Gateway
[4]User Name	[5]Password
[6]RS-232C Baud Rate	[7]Projector Name	[8]DHCP Client
[A]Advanced Setup		[D]Disconnect All
[V]View All Setting	[S]Save & Quit	[Q]Quit Unchanged
setup>

Note

•User name and password are not set in the fac- tory default settings.

•If the user name or password is entered incor- rectly three times, SETUP MENU will be quit.

3 Input“PJS11234”and press the“En- ter” key.

4 “OK”is displayed. Input“PJS25678” and press the “Enter” key within 10 seconds.

5

“User Name:”is displayed. Input the user name and press the “Enter” key.

•If a user name has not yet been set, just press the “Enter” key.

6

“Password:” is displayed. Input the password and press the“Enter”key.

•If a password has not yet been set, just press the “Enter” key.

-29

Image 29

Sharp XG-C330X, XG-C430X, XG-C335X Setting up the Projector Using RS-232C or Telnet, When Connecting Using RS-232C

Contents

XG-C430X XG-C335X XG-C330X SETUP MANUALLCD PROJECTOR MODELStandard Setup Front Projection Setting up the ScreenSide View Example of standard setupThrow Distance Screen Size and Projection DistanceThe graph below is for 100 inches 254 cm screen with 43 normal mode ScreenScreen Size and Projection Distance Standard Zoom LensF1.7-F1.9, f=28.0-33.6 mm Allow a margin of error in the value in the diagrams aboveF2.2-F2.7, f=24.5-30.7 mm Wide-zoom Lens AN-C12MZAllow a margin of error in the value in the diagrams above Screen Size and Projection DistanceF1.7-F2.2, f=36.5-46.3 mm Tele-zoom Lens AN-C18MZAllow a margin of error in the value in the diagrams above Screen Size and Projection DistanceF2.0-F2.8, f=53.8-82.9 mm Tele-zoom Lens AN-C27MZAllow a margin of error in the value in the diagrams above Screen Size and Projection DistanceF2.1-F2.8, f=83.5-117.2 mm Tele-zoom Lens AN-C41MZAllow a margin of error in the value in the diagrams above Screen Size and Projection DistanceRemove the protection cap from the back of the new lens Changing the LensRemove the lens by pulling it straight out 5 Insert the lens into the projector Replace the lens housing coverChanging the Lens RS-232C Cable recommended connection 9-pin D-sub female connector Connecting Pin AssignmentsSignal SignalDVI-D Input Terminal Connecting Pin AssignmentsPin No. Signal Pin No. SignalComputer control RS-232C Specifications and CommandsCommunication conditions Basic formatRS-232C Specifications and Commands CommandsExample When turning on the projector, make the following setting P O W RPARAMETER RS-232C Specifications and CommandsRS-232C Specifications and Commands 5 Lamp Timer Reset command is available only in standby mode RS-232C Specifications and CommandsPJLinkTM Compliant For additional information, visit “http//pjlink.jbmia.or.jp/english/”Network settings on the computer Setting up the Projector Network Environment1. Connecting the projector to a computer 2. Setting an IP address for the computerSetting up the Projector Network Environment 1. Connecting the Pro- jector to a Computer3 Plug the power cord into the AC socket of the projector 4 Turn on the computer2 Click “Start”, and click “Control Panel” 2. Setting an IP Address for the ComputerRight-click “Local Area Connec tion” and select “Properties”Setting up the Projector Network Environment jector”Setting up the Projector Network Environment 3. Setting up a Network Connection for the Projector1 Start Internet Explorer version Setting up the Projector Network Environment Click the “Apply” buttonControlling the Projector via LAN Controlling the Projector Using Internet ExplorerVersion 5.0 or later 1 Start Internet Explorer version 5.0 or later on the computerControlling the Projector Confirming the ProjectorControlling the Projector via LAN Status StatusSetting the Security Setting and Adjusting theProjector Settings & Adjustments Network - SecuritySetting for Sending E-mail when an Error Occurs Making General Settings for the Network NetworkMail - Originator Settings GeneralOccurs Service & Support Access URL Mail - Recipient SettingsExample of the display when an error occurs Controlling the Projector via LANWhen Connecting Using RS-232C Setting up the Projector Using RS-232C or Telnet7 Input “setup” and press the “Enter” key “Password” is displayed. Input the password and press the“Enter”keySetting up the Projector Using RS-232C or Telnet When Connecting Using Telnet6 Input “setup” and press the “Enter” key 5 “Password” is displayed. Input the password and press the“Enter”keyADVANCED SETUP MENU SETUP MENU Main MenuSetting up the Projector Using RS-232C or Telnet SETUP MENUVView All Setting View Setting Detail ListSet Items Setting up the Projector Using RS-232C or TelnetQuit without Saving Set Save Settings and QuitSSave & Quit tings QQuit UnchangedDefault Gateway Setting IP Address SettingSubnet Mask Setting User Name SettingProjector Name Setting Password SettingDHCP Client Setting 5PasswordSetting Auto Logout Time Disconnecting All ConnecEntering ADVANCED SETUP MENU Data Port SettingCarrying out Network Ping Test Setting of Accept IP Ad- dressAccepting All IP Addresses ADVANCED5Network Ping TestReturn to Default Settings Setting of Search PortADVANCED!Restore Default Setting Return to Main Menucode” field. From the “Connect using” drop-down menu, select Resetting the Lamp Timer of the Projector via LAN2 Enter a name in the “Name”field, and click “OK” 3 If you are required to enter the area code, enter it in the “Area6 Click the “Settings” tab, and then click “ASCII Setup” Resetting the Lamp Timer of the Projector via LANSend the lamp reset command “LPRE0001” 5 Click “Properties” on the “File” menuWhen connecting the projector using serial-connection TroubleshootingCheck the network settings for the computer and the projector For network settings for the projector, refer to pageUsage examples of ipconfig TroubleshootingC\ipconfig /? displays how to use “ipconfig.exe” C\ipconfigTroubleshooting Units inches mm DimensionsTop View Side ViewDimensions Projector and Lens DimensionsWhen AN-C12MZ is installed When AN-C18MZ is installed