Maintenance indicator | Problem |
| Cause |
| Possible Solution | ||
|
|
|
|
| |||
| Normal | Abnormal |
|
|
|
|
|
|
|
|
|
|
|
| |
Tempera- | Off | Red on | The internal | • | Blocked air intake | • Relocate the projector to | |
ture |
| (Standby) | temperature is |
|
|
| an area with proper |
warning |
|
| abnormally |
|
|
| ventilation. (See page 8.) |
indicator |
|
| high. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| • | Cooling fan | • | Take the projector to your |
|
|
|
|
| breakdown |
| nearest Sharp Authorized |
|
|
|
| • | Internal circuit |
| Projector Dealer or Service |
|
|
|
|
| failure |
| Center (see page 64) for |
|
|
|
| • | Clogged air intake |
| repair. |
Lamp | Green on | Red on | The lamp does | • | The lamp is shut | • Disconnect the power cord | |
indicator | (Green |
| not illuminate. |
| down abnormally. |
| from the AC outlet, and |
| blinks |
|
|
|
|
| then connect it again. |
| when the |
|
|
|
|
|
|
|
| Time to change | • | Remaining lamp life | • Carefully replace the lamp. | ||
| lamp is |
| |||||
|
| the lamp. |
| becomes 5% or |
| (See page 51.) | |
| warming |
|
|
| |||
|
|
|
| less. | • | Take the projector to your | |
| up or |
|
|
| |||
|
|
|
|
|
| nearest Sharp Authorized | |
| Red on | The lamp does | • |
| |||
| turning |
| |||||
|
| Projector Dealer or Service | |||||
| (Standby) | not illuminate. | • | Lamp circuit failure |
| ||
| off.) |
| |||||
|
| Center (see page 64) for | |||||
|
|
|
|
|
| ||
|
|
|
|
|
|
| |
|
|
|
|
|
|
| repair. |
|
|
|
|
|
| • Please exercise care when | |
|
|
|
|
|
|
| replacing the lamp. |
|
|
|
|
|
| • | Securely install the cover. |
|
|
|
|
|
|
| |
Power | Green on/ | Red | The power | • | The lamp unit cover | • If the power indicator blinks | |
indicator | Red on | blinks | indicator blinks |
| is open. |
| in red even when the lamp |
| Green |
| in red when the |
|
|
| unit cover is securely |
|
| projector is on. |
|
|
| installed, contact your | |
| blinks |
|
|
|
| ||
|
|
|
|
|
| nearest Sharp Authorized | |
| (Cooling) |
|
|
|
|
| |
|
|
|
|
|
| Projector Dealer or Service | |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| Center (see page 64) for |
|
|
|
|
|
|
| advice. |
|
|
|
|
|
|
|
|
Info
•If the temperature warning indicator illuminates, and the projector enters standby mode, follow the possible solutions above and then wait until the projector has cooled down completely before plug- ging in the power cord and turning the power back on. (At least 10 minutes.)
•If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illumi- nate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again.
•The cooling fan keeps the internal temperature of the projector constant and this function is con- trolled automatically. The sound of the cooling fan may change during operation because the fan speed may change and this is not a malfunction.
Appendix
49
