Sharp XV-Z200E 6, 7, 1, 2

Appendix

-61

6Insert the new lamp unit.

•Press the lamp unit firmly into the lamp

unit compartment. Fasten the secur-

ing screws.

7Attach the lamp unit cover.

•Slide the lamp unit cover in the direc-

tion of the arrow.

•Fasten the user service screw.

Resetting the Lamp

Timer

Reset the lamp timer after replacing the lamp.

1Plug the power cord.

•Confirm that the POWER indicator il-

luminates red.

2Reset the lamp timer.

•Press , , , , and

in order. Then press .

•“LAMP 0000H” is displayed on the

screen.

Info

•Make sure to reset the lamp timer only

when replacing the lamp. If you reset the

lamp timer and continue to use the same

lamp, the lamp may become damaged or

explode.

ON buttonUNDO button

INPUT button

ENTER button

Power cord

XV_Z200E_E_p57_66.p65 03.10.30, 13:15PM61

Contents

Main XV-Z200E SHARP CORPORATION XV-Z200E SPECIAL NOTE FOR USERS IN THE U.K. The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is Introduction Model No.: XV-Z200E Serial No.: -2 WARNING: XV_Z200E_E_p01_03.p65 03.10.30, 13:13PM2 Caution Concerning the Lamp Replacement There is potential glass particles hazard if the lamp ruptures. Introduction Contents Introduction Connections & Setup Basic Operation Adjustments and Settings IMPORTANT SAFEGUARDS ATTENTION Page -6 IMPORTANT SAFEGUARDS Be sure to read the following safeguards when setting up your projector. Caution concerning the lamp unit Cautions concerning the setup of the projector Do not set up the projector in places exposed to direct sunlight or bright light. Do not subject the projector to hard impact and/ or vibration. Quick Guide Required equipments Projector (Front and Top View) Numbers in refer to the main pages in this operation manual where the topic is explained. Projector (Side and Rear View) Part Names Projector (Rear View) Part Names Remote Control (Front View) Remote Control (Top View) Operating the Remote Control When using the remote control: Available Range of the Remote Control Inserting the Batteries 1 Accessories Power cord Optional accessories Supplied accessories Page Connecting the Projector to Other Devices Before Connecting This projector can be connected to: Video equipment: A computer using: 1 the projector. 2 the video equipment. 1 2 1 2 Connecting to a DVD Player and DTV Decoder 2 sub cable to the above adaptor. video equipment. Connecting to RGB Video Equipment Using the DVI to 15-pin D-sub Adaptor and the RGB Cable (INPUT 2) 2 an RGB cable. video equipment. Connecting to Video Equipment with the DVI Output Terminal Using a DVI Cable (DIGITAL INPUT) 1 TYPE switch on the back ter- minal board to VIDEO. 2 DIGITAL INPUT terminal. 3 2 an RGB cable. Connecting the thumbscrew cables Connecting to a com- puter with DIGITAL RGB output Terminal (DIGITAL INPUT) 1 TYPE switch on the back ter- minal board to PC. 2 jector. Plug and Play function 1 the projector. 2 Controlling the Projector by a Computer Setup Using the Swivel Stand 1 2 3 2 3 Focusing and Zooming 1 2 Using the Lens Shift Adjusting the Projection Distance -26 XV_Z200E_E_p25_28.p65 03.10.30, 13:13PM26 Setup - 0.038639669) Upper and Lower Lens Shift Position Upper and Lower Lens Shift Position (Ceiling Mount) Rear Projection Projection using a mirror Ceiling-mount setup Image Projection Setup Page Image Projection Basic Procedure 2 1 wall outlet. 3 on the remote control or on the projector to select the IN- PUT mode. Selecting the On- screen Display Lan- guage Display the Language menu and se- lect the desired Language. Turning the Power off 1 2 Basic Operation Horizontal Keystone Correction press again. 1 on the remote control. 2 stone or V Keystone. 3 1 2 3 4 5 2 Adjusting the Picture Aspect Ratio -36 XV_Z200E_E_p29_43.p65 03.10.30, 13:14PM36 Input Signal SIDE BAR SMART STRETCH Output screen image STRETCHCINEMA ZOOM Page Using the Menu Screen Menu Selections (Adjustments) 2 3 4 5 Using the Menu Screen 2 Menu Selections (Settings) 3 4 5 6 7 Menu Bar Items XV_Z200E_E_p29_43.p65 03.10.30, 13:14PM42 INPUT 1 / 2 / DIGITAL INPUT Mode Main menu Sub menu Main menu -43 INPUT 3 / 4 Mode Main menu Sub menu Main menu You can adjust the projectors picture to your preferences with the following picture set- tings. Adjusting the Picture Adjusting Image Prefer- ences Adjust the Picture menu on the menu screen. Adjusting the Colour Temperature Select CLR Temp in the Picture 1 ture menu on the menu screen and press . 2 '' ' or "" "" " to fine adjust the colour temperature. Gamma Correction Function Emphasizing the Contrast Picture Setting Function Storing the Adjustment Values for Each Memory Number Applying the Stored Settings Adjusting the Computer and DVD/DTV Images When Auto Sync is OFF Special Modes Adjust- ment Adjusting the Computer and DVD/DTV Images Auto Sync Adjustment Checking the Input Signal Using the Options Menu Checking the Lamp Life Status Display the Options menu to check the lamp life status. Turning on/off the On- screen Display Select OSD Display in the Options Selecting the Signal Type Setting the Video Signal (VIDEO menu only) Selecting a Background Image Setting the Eco Mode Using the Options Menu Automatic Power Shut- off Function Select Auto Power Off in the Options Selecting the Menu Screen Position Select Menu Position in the Options Selecting the Menu Colour Setting the Projection Mode Reversing/Inverting Projected Images Page Maintenance Indicators About the temperature warning indicator About the lamp indicator Regarding the Lamp Lamp Caution Concerning the Lamp Replacing the Lamp Caution 1 standby mode. 2 3 page 24.) 6 7 Resetting the Lamp Timer 1 2 Cleaning the Ventilative Holes Cleaning the Ventilative Holes 1 standby mode. 2 3 Using the Kensington Lock Troubleshooting -64 Connecting Pin Assignments RS-232C Port: 9-pin D-sub male connector 67 8 9 DVI-I (INPUT 2 / DIGITAL INPUT) port : 29 pin connector DVI Digital INPUT (RS-232C) Specifications and Command Settings C1 C2 C3 C4 P1 P2 P3 P4 Command 4-digit Parameter 4-digit O K Return code (0DH) E R R Return code (0DH) Computer Compatibility Chart -67 Specifications Specifications are subject to change without notice. Dimensions Units: mm Glossary Index XV-Z200E SHARP CORPORATION