Manuals
/
Brands
/
Computer Equipment
/
Projector
/
Sharp
/
Computer Equipment
/
Projector
Sharp
XV-Z200E
- page 59
1
59
73
73
Download
73 pages, 8.4 Mb
Appendix
Appendix
XV_Z200E_E_p57_66.p65
03.10.30, 13:15PM
57
Contents
Main
XV-Z200E
SHARP CORPORATION
XV-Z200E
SPECIAL NOTE FOR USERS IN THE U.K.
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is
Introduction
Model No.: XV-Z200E Serial No.:
-2
WARNING:
XV_Z200E_E_p01_03.p65 03.10.30, 13:13PM2
Caution Concerning the Lamp Replacement
There is potential glass particles hazard if the lamp ruptures.
Introduction
Contents
Introduction
Connections & Setup
Basic Operation
Adjustments and Settings
IMPORTANT SAFEGUARDS
ATTENTION
Page
-6
IMPORTANT SAFEGUARDS
Be sure to read the following safeguards when setting up your projector.
Caution concerning the lamp unit
Cautions concerning the setup of the projector
Do not set up the projector in places exposed to direct sunlight or bright light.
Do not subject the projector to hard impact and/ or vibration.
Quick Guide
Required equipments
Projector (Front and Top View)
Numbers in refer to the main pages in this operation manual where the topic is explained.
Projector (Side and Rear View)
Part Names
Projector (Rear View)
Part Names
Remote Control (Front View)
Remote Control (Top View)
Operating the Remote Control
When using the remote control:
Available Range of the Remote Control
Inserting the Batteries
1
Accessories
Power cord
Optional accessories
Supplied accessories
Page
Connecting the Projector to Other Devices
Before Connecting
This projector can be connected to:
Video equipment:
A computer using:
1
the projector.
2
the video equipment.
1
2
1
2
Connecting to a DVD Player and DTV Decoder
2
sub cable to the above adaptor.
video equipment.
Connecting to RGB Video Equipment Using the DVI to 15-pin D-sub Adaptor and the RGB Cable (INPUT 2)
2
an RGB cable.
video equipment.
Connecting to Video Equipment with the DVI Output Terminal Using a DVI Cable (DIGITAL INPUT)
1
TYPE switch on the back ter- minal board to VIDEO.
2
DIGITAL INPUT terminal.
3
2
an RGB cable.
Connecting the thumbscrew cables
Connecting to a com- puter with DIGITAL RGB output Terminal (DIGITAL INPUT)
1
TYPE switch on the back ter- minal board to PC.
2
jector.
Plug and Play function
1
the projector.
2
Controlling the Projector by a Computer
Setup
Using the Swivel Stand
1
2
3
2
3
Focusing and Zooming
1
2
Using the Lens Shift
Adjusting the Projection Distance
-26
XV_Z200E_E_p25_28.p65 03.10.30, 13:13PM26
Setup
- 0.038639669)
Upper and Lower Lens Shift Position
Upper and Lower Lens Shift Position (Ceiling Mount)
Rear Projection
Projection using a mirror
Ceiling-mount setup
Image Projection
Setup
Page
Image Projection
Basic Procedure
2
1
wall outlet.
3
on the remote control or on the projector to select the IN- PUT mode.
Selecting the On- screen Display Lan- guage
Display the Language menu and se- lect the desired Language.
Turning the Power off
1
2
Basic Operation
Horizontal Keystone Correction
press again.
1
on the remote control.
2
stone or V Keystone.
3
1
2
3
4
5
2
Adjusting the Picture Aspect Ratio
-36
XV_Z200E_E_p29_43.p65 03.10.30, 13:14PM36
Input Signal SIDE BAR SMART STRETCH
Output screen image STRETCHCINEMA ZOOM
Page
Using the Menu Screen
Menu Selections (Adjustments)
2
3
4
5
Using the Menu Screen
2
Menu Selections (Settings)
3
4
5
6
7
Menu Bar Items
XV_Z200E_E_p29_43.p65 03.10.30, 13:14PM42
INPUT 1 / 2 / DIGITAL INPUT Mode
Main menu Sub menu Main menu
-43
INPUT 3 / 4 Mode
Main menu Sub menu Main menu
You can adjust the projectors picture to your preferences with the following picture set- tings.
Adjusting the Picture
Adjusting Image Prefer- ences
Adjust the Picture menu on the menu screen.
Adjusting the Colour Temperature
Select CLR Temp in the Picture
1
ture menu on the menu screen and press .
2
'' ' or ""
"" " to fine adjust the colour temperature.
Gamma Correction Function
Emphasizing the Contrast
Picture Setting Function
Storing the Adjustment Values for Each Memory Number
Applying the Stored Settings
Adjusting the Computer and DVD/DTV Images
When Auto Sync is OFF
Special Modes Adjust- ment
Adjusting the Computer and DVD/DTV Images
Auto Sync Adjustment
Checking the Input Signal
Using the Options Menu
Checking the Lamp Life Status
Display the Options menu to check the lamp life status.
Turning on/off the On- screen Display
Select OSD Display in the Options
Selecting the Signal Type
Setting the Video Signal (VIDEO menu only)
Selecting a Background Image
Setting the Eco Mode
Using the Options Menu
Automatic Power Shut- off Function
Select Auto Power Off in the Options
Selecting the Menu Screen Position
Select Menu Position in the Options
Selecting the Menu Colour
Setting the Projection Mode
Reversing/Inverting Projected Images
Page
Maintenance Indicators
About the temperature warning indicator
About the lamp indicator
Regarding the Lamp
Lamp
Caution Concerning the Lamp
Replacing the Lamp
Caution
1
standby mode.
2
3
page 24.)
6
7
Resetting the Lamp Timer
1
2
Cleaning the Ventilative Holes
Cleaning the Ventilative Holes
1
standby mode.
2 3
Using the Kensington Lock
Troubleshooting
-64
Connecting Pin Assignments
RS-232C Port: 9-pin D-sub male connector
67 8 9
DVI-I (INPUT 2 / DIGITAL INPUT) port : 29 pin connector
DVI Digital INPUT
(RS-232C) Specifications and Command Settings
C1 C2 C3 C4 P1 P2 P3 P4
Command 4-digit Parameter 4-digit
O K Return code (0DH) E R R Return code (0DH)
Computer Compatibility Chart
-67
Specifications
Specifications are subject to change without notice.
Dimensions
Units: mm
Glossary
Index
XV-Z200E
SHARP CORPORATION