Setting the type of speakers | Depending or relationship between speakers, settings | |||||
The composition of the signals output from the different | possible for each speaker are as follows: |
| ||||
channels and the frequency reponse are adjusted |
|
|
|
|
| |
Front L/R Center | Surr. L/R | Surr. Back | Subwoofer | |||
automatically according to the combination of speakers | ||||||
actually being used. |
|
|
| Large |
| |
Select “Large” or “Small” not according to the actual size |
|
| Large | Small |
| |
|
|
|
|
| ||
of the speaker but according to the speaker’s capacity for |
| Large |
| None |
| |
playing low frequency (bass sound below frequency set for |
| Small | Large |
| ||
|
|
| ||||
the Crossover Frequency mode and below) signals. |
|
| Small |
| ||
|
|
|
| |||
|
|
|
|
|
| |
Large : Select this when connecting speakers that can fully |
|
|
| None |
| |
|
|
|
|
| ||
reproduce sounds below crossover frequency(*) of |
|
| None | X |
| |
your speaker. |
|
|
| Large |
| |
Small : Select this when connecting speakers that cannot |
|
| Large | Small | Yes | |
fully reproduce sound below crossover frequency. | Large |
|
|
| or | |
Small |
| None | ||||
When this setting is selected, sound below |
|
|
|
| ||
|
| Large | None | |||
crossover frequency is assigned to the subwoofer |
|
| Small | |||
|
|
|
| |||
|
| Small |
| |||
or speakers which are set to “Large”(when not |
|
|
|
| ||
|
|
|
|
| ||
|
|
| None |
| ||
using a subwoofer). |
|
|
|
| ||
None : Select this when no speakers are connected. |
|
| None | X |
| |
When this is selected, sound is sent to the front |
|
|
| Large |
| |
speakers. |
|
| Large |
|
| |
|
| Small |
| |||
Yes / None : Select the desired depending on whether a |
|
|
|
|
| |
| None |
| None |
| ||
subwoofer is connected or not. |
|
|
| |||
|
|
|
|
| ||
|
| Small | Large |
| ||
|
|
|
| |||
|
|
|
|
| ||
(*) : Crossover frequency is the frequency (Hz) below which the |
|
| Small |
| ||
|
|
|
| |||
|
|
| None |
| ||
bass sound of each main speakers is to output from the |
|
|
|
| ||
subwoofer or from speakers which are set to “Large” (when not |
|
| None | X |
| |
using a subwoofer). |
|
| Small | Small |
| |
Refer to the operating instructions of the speakers to be connected. |
|
|
| |||
| Small | None |
| |||
If the frequency range of your speaker is 100 Hz ~ 12 kHz, the |
|
|
| |||
Small |
|
|
| Yes | ||
crossover frequency have to set to 120 Hz. |
| None | X | |||
If you do not know, try comparing the sound at both settings |
|
|
|
|
| |
|
| Small | Small |
| ||
(setting the volume to a level low enough so as not to damage the |
| None |
|
| ||
| None |
| ||||
speakers) to determine the proper setting. |
|
|
| |||
|
|
|
|
| ||
|
|
| None | X |
|
Refer to the above and adjust the speaker settings
Note : When the SPEAKER button is set to off or the 7 CH DIRECT is selected as an input source, the speaker setting function cannot be available.
1 | When selecting each setting mode, | 2 | When adjusting the selected setting | ||||||
|
|
|
| mode to the desired setting, | |||||
SPEAKER |
|
|
|
|
|
|
|
|
|
SETUP |
|
|
|
|
| ADJUST |
|
|
|
|
|
|
|
|
|
|
|
| |
| or |
|
| SPK SET |
|
|
|
| ADJUST |
|
|
|
| or |
|
| <, > | ||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |
| 1 | 2 | 3 | 4 |
| 1 | 2 | 3 | 4 |
|
|
|
|
|
| ||||
|
|
|
|
|
| 5 | 6 | 7 | 8 |
• Each time the SPEAKER SETUP button is pressed, | • Each time the ADJUST UP( | / | ) or DOWN( / | ||||||
the speaker setting mode changes in succession and | |||||||||
is displayed for several seconds as follows. | ) button is pressed, one of the settings is selected | ||||||||
• When the speaker setting mode disappears, press the | and displayed for several seconds as follows. | ||||||||
SPEAKER SETUP button repeatedly to select the |
|
|
|
|
| ||||
desired mode. |
|
|
|
|
|
|
|
|
25