ENGLISH
Starting a Flooded Engine
WARNING!
Burn danger from hot engine! Allow engine to cool before removing cylinder cover.
Adjusting Engine Idle
The engine must return to idle speed whenever the throttle lever is released. Idle speed is adjustable, and must be set low enough to permit the engine clutch to disengage the cutters.
Stopping the Engine
Ignition OFF
Ignition
Switch
8
1. | Disconnect the spark plug lead, and |
| then use the spark plug wrench to |
| loosen and remove the spark plug. |
2. | If the spark plug is fouled or is soaked |
| with fuel, clean or replace the plug as |
| necessary. For spark plug specifica- |
| tions and gapping procedure, see page |
| 10. |
3. | With the spark plug removed, crank |
| the engine several times to clear |
| excess fuel from the combustion |
| chamber. |
HT231_15
Idle Adjustment
HT231_16
Figure 11
1.Cool the engine by allowing it to idle for
2.Move the ignition switch to the “O” or STOP position. See Figure 11.
.autorizado
9 Figura
| buj’a |
Bujia | la de Cable |
| |
| Cubierta |
14_HT231 |
|
4. Replace the spark plug and tighten it |
firmly with the spark plug wrench. If a |
Figure 10
Screw
¡ADVERTENCIA!
torque wrench is available, torque the |
spark plug to |
CAUTION!
Incorrect spark plug installation can damage the engine!
5.Replace the cylinder cover.
6.Repeat the starting procedures for a warm engine.
7.If the engine still fails to start or fire, refer to the troubleshooting chart at the end of this manual.
HT231_14
Cover
Spark
Spark PlugPlug
Lead
Figure 9
Idle Speed Adjustment
1.Start the engine, and then allow it to idle
2.If the cutters move when the engine is at idle, reduce idle speed by turning the idle adjustment screw counter- clockwise.
3.If a tachometer is available, the engine idle speed should be
3,000 ±250 rpm
4.Carburetor fuel mixture adjustments are preset at the factory and cannot be adjusted or serviced in the field.
WARNING!
The cutters must NEVER engage at engine idle speeds! If the idle speed cannot be adjusted by the above procedure, return the trimmer to your dealer for inspection.
.11 Figura Consulte .(apagado) O posición la a interruptor del botón el Mueva .2
.estabilice se motor del temperatura la que para minutos tres o dos por mínima marcha en opere el que Permita .1
11 Figura
.ajustar pueden se no y fábrica de calibración tienen carburador del mezcla la ajustar de tornillos Los .4
±3000 a mínima marcha de velocidad
la ajuste (tacómetro), tiempos | |
dos de motores para revoluciones | |
de medidor un disponible tiene Si .3 | |
.detengan de cuchillas | |
las que hasta reloj del manecillas | |
la a contrario sentido en mínima | |
marcha de ajuste de tornillo el gire | |
mínima, marcha en operando motor | |
el con mueven se cuchillas las Si .2 | |
| .operación |
de normal temperatura la alcance | |
que para minutos tres o dos por | |
opere que permita y motor el Arranque .1 | |
mínima: marcha la ajustar Para | |
m’nima marcha | 10 Figura |
| |
la ajustar para Tornillo | |
15_HT231 |
|
.manual este de final al |
|
diagnóstico guía el consulte arrancar, |
|
o encender en falla motor el aún Si | .9 |
.caliente motor un para |
|
arranque de procedimiento el Repita .8 | |
.cilindro del cubierta la Reinstale | .7 |
| |
|
,disponible torsión de llave una tiene Si .bujías de llave la con firmemente
apriétela y bujía la Reinstale .6
.motor el | |
buj’a la de incorrecta | |
¡PRECAUCIÓN! | |
.combustión |
|
de cámara la en combustible de exceso |
|
el eliminar para veces varias motor |
|
el arranque bujía, la retirada vez Una | .5 |
.calibración de proceso |
|
el y bujía la de especificaciones |
|
las para 21 página la Consulte |
|
.necesario sea según reemplácela |
|
o límpiela combustible, con |
|
impregnada o atorada esta bujía la Si | .4 |
.bujía la retirar y |
|
aflojar para bujías de llave la use luego |
|
y , bujía la de cable el Desconecte | .3 |
.cubierta la retire y cilindro del |
|
cubierta la de captivo tornillo el Afloje | .2 |
16_HT231
marcha de Interruptor
(O) Parada
.engranajes los de desacople se centrífugo embrague el que permita motor el que para motor, del especificaciones las a acuerdo de ajusta, se y regulable es mínima marcha La .libera se aceleración de gatillo el que momento todo en mínima marcha a volver de debe motor del velocidad La
.(parada) “O” posición la hacia marcha |
de interruptor del botón el Deslice .1 |
.cilindro |
del cubierta la retirar de antes |
enfrie motor el que Permita .caliente |
motor el por quemadura de ÁRiesgo |
¡ADVERTENCIA! |
ESPAÑOL
8
motor del normal Parada mínima marcha la de Ajuste | ahogado |
| motor un de Arranque |