27.11.98 Kap01.fm5 | Siemens A30853 instruction

27.11.98

kap01.fm5

Profiset 30isdn engl.: A30853-X300-B107-1-7619

Programming the telephone settings

Signalling method to control the ISDN services

a

S08

T

1... 4

0 or 1

S

In most of the countries local network operators use the socalled “functional protocol” to control the following ISDN services:

●1 Call Forwarding Unconditional (CFU)

●2 Advice of Charge (AOC)

●3 Hold, Consultation/Toggling (HOLD)

●4 Three-party conference (3PTY)

The default settings of your Profiset 30isdn is preset to the functional protocol. If the above-mentioned ISDN services work correctly (➔ page 12, 22, 23, 34), you should keep on controlling these services via functional protocol.

In some countries, however, keypad signalling is used to control the above ISDN services instead of the functional protocol. You will recognize that when it is possible to control the ISDN services by entering keypad sequences (e.g. *21#, *#21# a.s.o.).

To find out which ISDN services are controlled by keypad signalling in your country, contact your local network op- erator.

Handset is on-hook.

Start the programming procedure.

Enter the password if necessary.

Enter the code (1 ... 4) for the ISDN service.

Enter the code (0 or 1) for the signalling method.

Save the settings.

Note:

if you change the national variant (➔ page 32), the signalling method for all ISDN services is set to functional protocol.

33

Image 41

Siemens A30853 operating instructions 27.11.98 Kap01.fm5

Contents

Profiset 30isdn Your guide to this manual Profiset 30isdnProfiset 30isdn Profiset 30isdn Overview Profiset 30isdn Profiset 30isdn Overview Keys Location of the telephone Safety precautions and approvalSafety precautions Profiset 30isdn Approval and conformity Contents Contents Putting the telephone into operation Symbols used in these operating instructionsPutting the telephone into operation Isdn connecting cord Handset cord coiled Handset cord coiled Telephone connecting cordPutting the telephone into operation Connect the telephone Ntba Program the multiple subscriber numbers MSNs PBX operation only Program the trunk code Setting the national variants Taking a call Putting the telephone into operation Try out the telephoneCalling another party Digit display line Display Idle mode SymbolsDisplay-driven telephone operation Display-driven telephone operation 030234577 001.20 045672343 Connected mode Calling users On-hook dialling Outgoing and incoming callsOutgoing and incoming calls Outgoing and incoming calls Number redial automatic dialling Is displayed Call forwarding Outgoing and incoming calls Accepting a callRejecting a call Disconnect Outgoing and incoming calls Call waiting Deactivating the call signal Do not disturbAccepting call waiting Rejecting call waiting Retrieving entries from the call list Outgoing and incoming calls Call listDialling a number from the call list Storing a number from the call list Initiating a callback CallbackDeleting the call list Clearing a callback Ending a call disconnectingAccepting a callback Convenient and secure telephone communication Switching to mute consultation in the roomConvenient and secure telephone communication Activating/deactivating open listening Resuming a parked call Convenient and secure telephone communication Parking a call 27.11.98 Kap01.fm5 Keypad signalling Dtmf Calls involving two or more parties Switching between two calling parties togglingCalls involving two or more parties Calling the second party consultation Three-party conference Disconnecting one party Calls involving two or more parties Ending a conference Ending a conference by disconnecting a partyEnding a conference and toggling between parties Exiting from a conference Programming keys on the telephone Programming keys on the telephoneProgramming the destination dialling keys Programming the speed dialling keys Programming direct station selection babyphone Quick reference for available telephone settings Quick reference for available telephone settingsTelephone settings Description Password Programming the telephone settingsProgramming the telephone settings Ringer melody Programming the telephone settings Ringer volume Call processing type S06 T 0 or Following settings are possible Multiple Subscriber Numbers MSN Programming the telephone settings National variants 27.11.98 Kap01.fm5 Call number for call forwarding unconditional Date/time Tariff unit factor Enter the call number for call forwarding Save the setting Call is deactivated S14 T Clearing the summation meter Enabling/disabling call waiting Checking the settings status Programming the telephone settings Clearing memory Displaying the software version Important information for installation and operation Important information for installation and operationMaintenance Removing and inserting the labelling cards Technical data Default settings Third party use/disposal Siemens Service Symptom Cause Action Isdn glossary Isdn glossary Isdn glossary Isdn glossary Toggling d è R è R Quick reference guideQuick reference guide Quick reference for available telephone settings Index Index Technical data 27.11.98 Back.fm5 Siemens Aktiengesellschaft