Siemens AS 488/TM Coupling to other systems with DP interface, Coupling to PROFIBUS-PA, ET 200U

This catalog is out of date, see note on page 3

Coupling to other systems with

DP interface

• SIMATIC S7 CPU 315-2 DP	When using floating-point num-
	bers, see supplementary pack-
	age "DP extensions for
	AS x88/TM"
• SIMATIC S7 CPU 316-2 DP	When using floating-point num-
	bers, see supplementary pack-
	age "DP extensions for
	AS x88/TM"
• SIMATIC S7 CPU 318-2 DP	When using floating-point num-
	bers, see supplementary pack-
	age "DP extensions for
	AS x88/TM"
• SIMATIC S7 CP 340	When using floating-point num-
	bers, see supplementary pack-
	age "DP extensions for
	AS x88/TM"
• DP/DP coupler	When using floating-point num-
	bers, see supplementary pack-
	age "DP extensions for
	AS x88/TM"
• S5-95	When using floating-point num-
	bers, see supplementary pack-
	age "DP extensions for
	AS x88/TM"
• S5-95F
Coupling to PROFIBUS-PA

AS 488 in SIMATIC design

	Introduction
	AS 488/TM
Quantity breakdown
Automation performance	Approx. 150 % or 270 to 300 %
	of AS 235 automation system
	performance depending on CPU
Memory for user-specific applica-	4 Mbyte
tions
Typical quantity breakdown data
• Number of control loops	45 to 120
• Additional analog value monitoring	45 to 180
• Sequential controls	8 to 20
• Logic controls	150 to 370
Redundancy
AS 488/TM CPU	No
CS 275	Yes, as option
PROFIBUS-TM, PROFIBUS-DP	Yes, with OLM P/G12 optical link
	module
Configuring
Tools	PROGRAF AS+/NT, commission-
	ing terminal software,
	COM PROFIBUS
Connection	PROGRAF AS+/NT via PROFI-
	BUS-TM/CS 275, commission-
	ing terminal software via COM1
	interface of IF 962-COM inter-
	face module

• Coupling of PA devices using	Max. 122 stations on 45.45 kbit/s
DP/PA coupler	DP bus
	Special drivers required; see
	supplementary package "Con-
	nection of PROFIBUS-PA to
	AS x88/TM"
• Coupling of PA devices using	Max. 122 links; up to 10 or 30 PA
DP/PA link	devices can be connected per
	DP/PA link depending on the
	device type
	Special drivers required; see
	supplementary package "Con-
	nection of PROFIBUS-PA to
	AS x88/TM"
Coupling to intelligent DP field
devices and to DP devices from
other vendors
• SIPART DRxx controller	Required special drivers on
	request 1)
• SIMOCODE motor control	Required special drivers on
	request 1)
• SIMOVERT converter	Required special drivers on
	request 1)
• I.S.1 field stations from Stahl	Required special drivers on
	request 1)
• Analog modules from CEAG	Required special drivers on
	request 1)
• ACS 600 frequency converter	Required special drivers on
	request 1)
ET 200U
• Function modules	Yes, controllers
• Signal modules	Yes
• Coupling modules	Yes
ET 200B
• Signal modules	Yes

Ambient conditions

Degree of protection to EN 60 529	IP 20
Permissible ambient temperature
• Operation (horizontal installation)	0 to 60 °C
• Transport and storage	-40 to +70 °C
Permissible relative humidity	5 to 95 %
Operation without fans	Yes
Electrical isolation
• On PROFIBUS-TM	Yes
• On PROFIBUS-DP	Yes
Design
Dimensions (H x W x D) in mm
With SIMATIC S7/M7 rack	290 x 240 x 220 (plus plug)
With migration rack	380 x 483 x 273

1)Required special drivers on request from Roland.Heid@siemens.com, Tel. +49 721 595-6380, Fax. +49 721 595-6383

All modules configurable with COM PROFIBUS can be connect- ed via PROFIBUS-DP, and are recorded in the process image of the AS 488/TM system.

Further requirement:

The data interface of a station on the PROFIBUS-DP fieldbus must be described. Please contact our support line for driver blocks for other DP devices from the SIMATIC range or from oth- er Siemens Groups or also from other vendors:

SupportLine,

Tel. +49 180 5050 222,

Fax +49 180 5050 223,

E-mail: adsupport@siemens.com.

Siemens PLT 112 · 2002 5/3