Silvercrest SHDP 5.1 A1 OSD menu settings, Using the OSD Menu, Setup menu General, TV Display

10. OSD menu settings

All of the DVD player's settings can be made with the remote control via the so called "On Screen Display" menu ("OSD menu" for short). The OSD Menu will be superimposed on the television screen.

Note:

In these instructions the English OSD menu is described. At any time you can set the menu to your country's language as described in "GENERAL > OSD LANGUAGE".

GENERAL	AUDIO	DOLBY	VIDEO	PREFERENCE
TV DISPLAY		PS
ANGLE MARK		ON
OSD LANGUAGE		ENG
CLOSED CAPTIONS		OFF
SCREEN SAVER		ON
LAST MEMORY		OFF

Before you use the DVD player for the first time for playback of DVDs, VCDs/S-VCDs or audio/MP3-CDs you must implement a few settings via the OSD Menu. These settings are dependent amongst others on...

•the language, in which you want the OSD menu to be displayed

•which TV standard corresponds to the television, to which you want to connect the DVD player

•Which image format your television can display

Administering settings via the OSD menu

•First insert the connector plug of the DVD player's power cord into a power socket.

•To switch the DVD player on activate the POWER switch on the rear panel of the DVD player. If the DVD player is already switched on but is in standby mode, press the button STANDBY on the remote control to switch the DVD player on. The standby mode is identified by the LED in

the display on the front panel of the device.

The device will check to see if a disc is inserted. The SilverCrest logo appears on the television screen:

If no disc is inserted the notification NO DISC appears on the television screen and in the display.

•Firstly please familiarize yourself with the OSD Menu's operation by means of the following brief introduction.

10.1 Using the OSD Menu

•To access the DVD players OSD menu press the SETUP button on the remote control. The OSD Menu with its menu options will appear on the television screen:

GENERAL	AUDIO	DOLBY	VIDEO	PREFERENCE
TV DISPLAY		PS
ANGLE MARK		ON
OSD LANGUAGE		ENG
CLOSED CAPTIONS		OFF
SCREEN SAVER		ON
LAST MEMORY		OFF

The following menu options can be selected:

GENERAL, AUDIO, DOLBY, VIDEO and PREFERENCE.

•	With the control buttons	and the ENTER button you can carry
	out all the settings in the menu.
•	With the control buttons	you can select a menu by moving the yellow
	marking onto the corresponding menu symbol.
•	With the control buttons	you select an input in a menu by moving
	the green bar over an input.
•	With the control button	you change an input in the sub menu and with
	the control button you move back to the previous menu level.

•To confirm a selection press the ENTER button.

All navigation possibilities in a current menu are displayed at the lower edge of the menu.

•To exit the OSD menu press the SETUP button again.

10.2 Setup menu GENERAL

In this menu you can, for example, set the image presentation or the language of the OSD menu.

GENERAL	AUDIO	DOLBY	VIDEO	PREFERENCE
TV DISPLAY		PS
ANGLE MARK		ON
OSD LANGUAGE		ENG
CLOSED CAPTIONS		OFF
SCREEN SAVER		ON
LAST MEMORY		OFF

TV DISPLAY

-4:3/PANSCAN Select this setting to display broadcasts in the usual 4:3 format on a 4:3 television set. Broadcasts in the 16:9 format will be displayed in full screen without the distracting bars although the side edges of the image will be trimmed.

-4:3/LETTERBOX Display of a film in 16:9 format on a traditional 4:3 format television. The image is displayed with black bars on the lower and upper edges of the screen.

-16:9This setting is recommended when using a wide screen television in 16:9 format. An image in 4:3 format will be adapted horizontally to the image width.

-Wide Squeeze An image in 4:3 format will be presented with black bars on the right and left edges.

- 8 -