ADVANCED PROGRAMMING
OPERATION
System Status
|
|
|
|
| ® |
|
|
|
|
|
|
|
|
|
|
| |
| SENSOR 1 | SENSOR 2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Zone 1 | Button [1] | Button [6] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Zone 2 | Button [2] | Button [7] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Zone 3 | Button [3] | Button [8] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
Zone 4 | Button [4] | Button [9] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Zone 5 | Button [5] | Button [0] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This row : Buttons for Sensor 1
Zone LED : Flash once
This row : Buttons for Sensor 2
Zone LED : Flash twice
The control panel continuously monitors the system status as well as all the sensors status. It will monitor occurrences such as triggered sensors, low battery sensors, malfunction sensors, or phone line failure etc.
In order to check the system status, user can press the “Status” button on the control panel, voice announcement will be made regarding the system and sensor status. When the “Status” button is pressed, you will be notified if any of the following events is occurring:
- System armed or disarmed - Any triggered sensors
Erase Sensors
Proceed to the following to erase a sensor.
| Step |
| Keys |
| Function | Description | Note |
|
|
|
|
|
|
|
|
| 1 |
| [PROG] |
| Enter | Enter master | 3 beeps for v alid password. |
|
|
| [MPIN] |
| Programming | password to | 1 long beep for invalid |
|
|
|
|
| mode | programming mode | password. |
|
|
|
|
|
|
|
|
| 2 |
| [9] |
| Select erase |
| After [9] is entered, some |
|
|
|
|
| remote |
| zone LEDs will flash or |
|
|
|
|
| programming |
| stay off. The zone LEDs |
|
|
|
|
|
|
| represent whether that zone |
|
|
|
|
|
|
| is occupied by any sensor. |
|
|
|
|
|
|
| **See Table D below. |
| 3 |
| To erase an | Select the | Refer to the table | After you have selected the | |
|
|
| occupied |
| sensor you | below to select the | sensor, you will hear 3 beeps |
|
|
| sensor, press | would like to | remote location. | and verbal confirmation | |
|
|
| [1] to [0]. |
| erase |
| [Zone X Sensor Y Empty |
|
|
|
|
|
|
| Memory], where X and Y |
|
|
|
|
|
|
| are the zone and sensor |
|
|
|
|
|
|
| numbers you have selected. |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| ZONE LED |
| DESCRIPTION |
|
| ||
|
|
|
|
| |||
| Off |
| Zone is not occupied by any sensor |
| |||
|
|
|
| ||||
| Flashes once | This zone is occupied by sensor 1. |
| ||||
|
|
|
| ||||
| Flashes twice | This zone is occupied by sensor 2. |
| ||||
|
|
| |||||
| Flashes once, | This zone is occupied by sensors 1 and 2. | |||||
| then twice |
|
|
|
|
| |
|
|
|
|
|
|
|
|
**Table D: Zone LED status for erasing sensors.
- Any sensors with low battery warning - Any sensors with failure warning
- Phone line failure
Refer to page 20 for more details regarding system failures.
Arming the System
You should arm the system when you are the last person to leave the house. By arming the system, the control panel will call the preprogrammed emergency phone numbers and the siren will sound when
Caution: Only arm the system when nobody is expected to be inside the premises. When someone is expected to be within the premises, the system should not be armed.
To arm the system, follow the procedures below:
Exit delay 45 seconds | 45 seconds later | ||||
Beep Beep | ARM LED on. System | ||||
|
| Armed | |||
|
|
|
|
|
|
|
|
|
|
|
|
1. Press [Arm] on the control | 2. Leave the premises | 3. After 45 seconds. |
panel. | within 45 seconds. | System will be armed. |
1. Press [Arm] button on the control panel when no sensors are triggered.
