Slant/Fin S-150, SX-210, SX-150 dimensions Natural GAS-FIRED Boiler Location, Boiler Foundation

Sentry																								3
																				Approx.
										Dimensions
											(inches)									Total Wt.
																				Full of
	Boiler		No. of
																		G		Water (lb.)
	Model		Sect.			A		B	C				D		E		F					CHIMNEY RECOMMENDATIONS
																		(max)
																						HEIGHT:15 ft. (minimum) from draft
	S-34		2		81⁄8"		145⁄8"		4			33"			—		—	61⁄4"	190
																						hood skirt to top of chimney.
	S-60		3	111⁄8"			175⁄8"		4			37"			41⁄2"	26"		61⁄4"	250
																						INSIDE DIAMETER: Same as dimen-
	S-90		4	141⁄8"			205⁄8"		5			37"			51⁄2"		251⁄2"	61⁄4"	310			sion C (or larger).
	S-120		5	171⁄8"			235⁄8"		6			37"			71⁄2"	25"		61⁄4"	365			NOTE: Larger chimney may be
																						required if two or more boilers or a boil-
	S-150		6	201⁄8"			265⁄8"		7			37"			81⁄2"		241⁄2"	81⁄4"	425			er and another appliance are vented to
																						a single chimney.
	SX-150		6	201⁄8"			265⁄8"		6			511⁄2"		101⁄2"			107⁄8"	61⁄4"	425
																						Slant/Fin supplies vent dampers by
	SX-180		7	231⁄8"			295⁄8"		7			523⁄4"		12"			107⁄8"	81⁄4"	485			several manufacturers. Some are
	SX-210		8	261⁄8"			325⁄8"		7			523⁄4"		131⁄2"			107⁄8"	81⁄4"	545			smaller than the indicated “G maxi-
																						mum”.
								Orifice							Orifice Sizes			for High Altitudes
														Includes 4% Reduction for Each 1000 Feet
								Size for
	Boiler					Gas											Elevation - Feet
								Sea
	Model					Type		Level	2000				3000		4000		5000	6000		7000	8000		9000	10000
		S-34				Natural		47	48				48		49		49	49		50	50		51	51
						Propane		56	56				56		57		57	57		58	59		59	60
S-60 thru S-150 and						Natural		50	51				51		51		51	52		52	52		53	53
SX-150 thru SX-210						Propane		57	58				59		59		60	60		61	62		63	63

Orifice indicated for sea level above are factory installed in boiler unless otherwise specified by the local authority. See III page 10 for burner input adjustment.

Base Assembly Sentry Boiler

Burners

Pilot

Burner

Access

Door

Gas Valve

INSTALLATION REQUIREMENTS

The installation must conform to the requirements of the authority having jurisdiction or, in the absence of such requirements, to the National Fuel Gas Code, ANSI Z223.1-latest edition.

This installation must also conform to the additional requirements in this Slant/Fin Instruction Book.

NATURAL GAS-FIRED BOILER LOCATION

Provide a level, solid foundation for the boiler. Location should be as near as possible to chimney or outside wall so that the flue pipe from boiler is short and direct.

The location should also be such that the gas ignition system com- ponents are protected from water (dripping, spraying, rain, etc.) during appliance operation and service (circulator replacement, condensate trap, control replacement, etc.).

BOILER FOUNDATION

A. Provide a solid, level foundation, capable of supporting the weight of the boiler filled with water, and extending at least 2" past the jacket on all sides. See dimensions of boiler, page 2.

B. For installation on non-combustible floors only. The Combustible Floor Kit part number printed on the boiler rating plate is the only one to be used when installing on combustible floors. The boiler must not be installed on carpeting.

C. If boiler is to be located over buried conduit containing electric wires or telephone cables, consult local codes or the National Board of Fire Underwriters for specific requirements.