Installing an Optional Module into the Switch | SMC Networks 100

INSTALLING THE SWITCH

Installing an Optional Module into the Switch

Optional modules are available for media expansion, stacking and management. These modules can be installed into the modular slots on the rear panel of the switch. The Network Management Module must be installed in the upper slot, and the Stack Module in the lower-left slot. The media expansion modules can be installed in either of the two lower slots.

Caution: DO NOT install slide-in modules with the switch powered on. Be sure you power off the switch before installing any module.

To install an optional module into the switch, do the following:

1.Disconnect power to the switch.

2.Remove the blank metal plate (or a previously installed module) from the appropriate slot by removing the two screws with a flat-head screwdriver. A media module can be installed in either of the two lower slots on the rear panel of the switch. A Network Management Module can be installed in the upper slot on the rear of the switch.

3.Before opening the package that contains the module, touch the bag to the switch casing to discharge any potential static electricity. Also, use the ESD wrist strap included with the package.

4.Remove the module from the anti-static shielded bag.

5.Holding the module level, guide it into the carrier rails on each side and gently push it all the way into the slot, ensuring that it firmly engages with the connector.

3-6

Image 44

SMC Networks 100 manual Installing an Optional Module into the Switch

Contents

TigerSwitch Page TigerSwitch Installation Guide Trademarks Limited Warranty Limited Warranty EC Conformance Declaration Class a CompliancesFCC Class a Industry Canada Class a Safety Compliance IiiWarnhinweis Faseroptikanschlüsse Optische Sicherheit Underwriters Laboratories Compliance Statement Wichtige Sicherheitshinweise Germany Table of Contents Making Network Connections Vii Viii Chapter About Tigerswitch Overview Switch Architecture Optional Modules 100BASE-FX VF-45 Ports Description of HardwareManagement Options Status LEDs Port and System LEDs Network Management Module Network Management Module Spanning Tree Protocol VLANs Multicast Switching Optional Media Extender ModulesTraffic Priority Optional 100BASE-FX Module SMC6900FSC Optional 1000BASE-LX Module SMC6900GLSC Optional 100BASE-FX Module SMC6900FSSCOptional 1000BASE-SX Module SMC6900G Optional Stack Module SMC6900S Optional Redundant Power Unit SMCRPU150WOptional 1000BASE-T Module SMC6900GT Power Supply Receptacles 12. Power Supply Receptacles Expandability Features and BenefitsConnectivity Performance Management About the Tigerswitch About the Tigerswitch Introduction to Switching Chapter Network Planning Sample Applications Collapsed Backbone Central Wiring Closet Central Wiring Closet Collapsed Backbone Using Fiber Cable Remote Connections with Fiber Cable Making Vlan Connections Making Vlan Connections Connectivity Rules Mbps Gigabit Ethernet Collision DomainMaximum 1000BASE-T Optic Cable Distance Maximum 1000BASE-SX Fiber Optic Cable Distance Maximum Network Diameter Using Repeaters Mbps Fast Ethernet Collision DomainMaximum 100BASE-FX Fiber Optic Cable Distance SMC 3-2 Rule for Class II Repeaters Cable Type Connecting Max. Distance Maximum Fast Ethernet Cable Distance Application Notes Network Planning Installing the Switch Selecting a Site Optional Rack-Mounting Equipment Equipment ChecklistPackage Contents Mounting Rack Mounting Attaching the Brackets Desktop or Shelf Mounting Attaching the Adhesive Feet Installing an Optional Module into the Switch Installing a Module Stacking Stacking the Switches Connecting to a Power Source Power Receptacle Installing the Switch Connecting Network Devices Chapter Making Network Connections VF-45 Fiber Connections SC Fiber Connections Making SC Port Connections Cabling Guidelines Connecting to PCs, Servers, Hubs and Switches1000BASE-T Twisted-Pair Connections Making Twisted-Pair Connections Wiring Closet Connections Wiring Closet Connections Making Network Connections Appendix a Troubleshooting Diagnosing Switch Indicators In-Band Access Power and Cooling ProblemsInstallation Troubleshooting Troubleshooting Specifications Appendix B Cables Cables RJ-45 Port and Cable Assignments 1000BASE-T Pin Assignments Cable Testing for Existing Category 5 Cable 1000BASE-T Cable Requirements Adjusting Existing Category 5 Cabling Console Port Pin Assignments DB-9 Port Pin Assignments Console Port to 25-Pin DTE Port on PC Console Port to 9-Pin COM Port on PCConsole Port to 25-Pin DCE Port on Modem Cables Appendix C Specifications Physical Characteristics Weight TemperaturePower Supply Power Consumption Switch Features Management Features Compliances WarrantyStandards 1000BASE-SX Extender Module Slide-in Module100BASE-FX Extender Module 1000BASE-LX Extender Module 1000BASE-T Extender Module Stack Module Connector InterfaceAgent Module Appendix D Ordering Information Ordering Information Glossary Glossary-11000BASE-T Auto-Negotiation Glossary-2 Glossary-3 Glossary-4 Glossary-5 Virtual LAN Vlan Glossary-6Transmission Control Protocol/Internet Protocol TCP/IP Index Index-1 Index-2 Index-3 See RPU Index-4 Page Internet