SMC Networks 10G specs

COMPLIANCES

CE Mark Declaration of Conformance for EMI and Safety (EEC)

SMC contact for these products in Europe is:

SMC Networks Europe, Edificio Conata II,

Calle Fructuós Gelabert 6-8, 2o, 4a,

08970 - Sant Joan Despí, Barcelona, Spain.

This information technology equipment complies with the requirements of the Council Directive 89/336/EEC on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain voltage limits and the Amendment Directive 93/68/EEC. For the evaluation of the compliance with these Directives, the following standards were applied:

RFI Emission:	• Limit class A according to EN 55022:1998
	• Limit class A for harmonic current emission according to
	EN 61000-3-2/1995
	• Limitation of voltage fluctuation and flicker in low-voltage supply
	system according to EN 61000-3-3/1995
Immunity:	• Product family standard according to EN 55024:1998
	• Electrostatic Discharge according to EN 61000-4-2:1995
	(Contact Discharge: ±4 kV, Air Discharge: ±8 kV)
	• Radio-frequency electromagnetic field according to EN 61000-4-3:1996
	(80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m)
	• Electrical fast transient/burst according to EN 61000-4-4:1995 (AC/
	DC power supply: ±1 kV, Data/Signal lines: ±0.5 kV)
	• Surge immunity test according to EN 61000-4-5:1995
	(AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV)
	• Immunity to conducted disturbances, Induced by radio-frequency
	fields: EN 61000-4-6:1996 (0.15 - 80 MHz with
	1 kHz AM 80% Modulation: 3 V/m)
	• Power frequency magnetic field immunity test according to
	EN 61000-4-8:1993 (1 A/m at frequency 50 Hz)
	• Voltage dips, short interruptions and voltage variations immunity test
	according to EN 61000-4-11:1994 (>95% Reduction @10 ms, 30%
	Reduction @500 ms, >95% Reduction @5000 ms)
LVD:	• EN 60950 (A1/1992; A2/1993; A3/1993; A4/1995; A11/1997)

Warning: Do not plug a phone jack connector in the RJ-45 port. This may damage this device. Les raccordeurs ne sont pas utilisé pour le systéme téléphonique!

iv

Image 8

SMC Networks 10G manual CE Mark Declaration of Conformance for EMI and Safety EEC

Contents

TigerStack 10G Page TigerStack 10G Installation Guide Trademarks Limited Warranty SMC Networks, Inc Tesla Irvine, CA Compliances FCC Class aIndustry Canada Class a Japan Vcci Class a CE Mark Declaration of Conformance for EMI and Safety EEC Warnhinweis Faseroptikanschlüsse Optische Sicherheit Safety ComplianceTaiwan Bsmi Class a Australia AS/NZS 3548 1995 Class a Power Cord Safety France and Peru only Vii Viii Environmental Statement End of Product Life SpanManufacturing Materials Documentation Purpose Related Publications Table of Contents Making Network Connections Appendices Xiv Tables Xvi Figures Xviii Chapter About Tigerstack 10G Overview Switch Architecture SMC8748M and SMC8724M Front Panels 10/100/1000BASE-T Ports Description of HardwareManagement Options SFP Slots Stacking Ports Status LEDs Port LEDs Port Status LEDs System Status LEDs System Status LEDs Features and Benefits Optional Redundant Power UnitPower Supply Receptacles Connectivity Management ExpandabilityPerformance About the Tigerstack 10G Introduction to Switching Chapter Network Planning Application Examples Collapsed Backbone Network Aggregation Plan Network Aggregation Plan Remote Connections with Fiber Cable Remote Connection with Fiber Cable Making Vlan Connections Making Vlan Connections Application Notes Installing the Switch Selecting a Site Ethernet Cabling RJ-45 Connections Optional Rack-Mounting Equipment Equipment ChecklistPackage Contents Mounting Rack Mounting Attaching the Brackets Desktop or Shelf Mounting Attaching the Adhesive Feet Installing an Optional SFP Transceiver into the Switch Inserting an SFP Transceiver into a Slot Connecting Switches in a Stack Making Stacking Connections Stacking Topologies Connecting to a Power Source Power Receptacle Connecting to the Console Port Serial Port DB-9 DTE Pin-Out Installing the Switch Connecting Network Devices Chapter Making Network ConnectionsTwisted-Pair Devices Cabling Guidelines Connecting to PCs, Servers, Hubs and Switches Making Twisted-Pair Connections Network Wiring Connections Wiring Closet Connections Fiber Optic SFP Devices Making LC Port Connections Connectivity Rules 1000BASE-T Cable RequirementsMbps Gigabit Ethernet Collision Length Maximum 1000BASE-T Gigabit Ethernet Cable Length Mbps Fast Ethernet Collision Domain Mbps Ethernet Collision Domain Cable Labeling and Connection Records Table A-1 Troubleshooting Chart Appendix a TroubleshootingDiagnosing Switch Indicators Power and Cooling Problems Installation In-Band Access Stack Troubleshooting Troubleshooting Appendix B Cables Twisted-Pair Cable and Pin Assignments Table B-1 10/100BASE-TX MDI and MDI-X Port Pinouts Straight-Through Wiring10BASE-T/100BASE-TX Pin Assignments Crossover Wiring Figure B-2 Straight-through Wiring 1000BASE-T Pin Assignments Table B-2 1000BASE-T MDI-X and MDI Port Pinouts Cable Testing for Existing Category 5 Cable Adjusting Existing Category 5 Cabling to Run 1000BASE-T Fiber Standards Appendix C Specifications Physical Characteristics Weight TemperaturePower Supply Power Consumption Standards Switch FeaturesManagement Features Warranty SafetyCompliances CE Mark Emissions Appendix D Ordering Information Ordering Information Auto-Negotiation Glossary1000BASE-T Bandwidth CollisionCollision Domain End Station Gigabit Ethernet Full DuplexIeee Ieee 802.3ab Media Access Control MAC Redundant Power Unit RPURJ-45 Connector Switched Ports Transmission Control Protocol/Internet Protocol TCP/IP Virtual LAN Vlan Glossary-6 Index Numerics Index-2 Index-3 Index-4 Page For Technical SUPPORT, Call