SMC Networks 10G Mounting

NSTALLING

THE

WITCH

3-4

Mounting

A TigerStack 10G unit can be mounted in a standard 19-inch equipment

rack or on a desktop or shelf. Mounting instructions for each type of site

follow.

Rack Mounting

Before rack mounting the switch, pay particular attention to the following

factors:

◆Temperature: Since the temperature within a rack assembly may be

higher than the ambient room temperature, check that the

rack-environment temperature is within the specified operating

temperature range. (See page C-2.)

◆Mechanical Loading: Do not place any equipment on top of a

rack-mounted unit.

◆Circuit Overloading: Be sure that the supply circuit to the rack

assembly is not overloaded.

◆Grounding: Rack-mounted equipment should be properly grounded.

Particular attention should be given to supply connec tions other than

direct connections to the mains.

Contents

Main TigerStack 10G Gigabit Ethernet Switch Installation Guide Page Page Trademarks: L W IMITED ARRANTY ii iii OMPLIANCES Japan VCCI Class A FCC - Class A Industry Canada - Class A iv CE Mark Declaration of Conformance for EMI and Safety (EEC) v Taiwan BSMI Class A Australia AS/NZS 3548 (1995) - Class A Safety Compliance vi Power Cord Sa fety vii Veuillez lire fond l'information de la scurit suivante avant d'installer le Switch: viii Bitte unbedingt vor dem Einbauen des Switches die folgenden Sicherheitsanweisungen durchlesen: ix Warnings and Cautionary Messages Environmental Statement End of Product Life Span Manufacturing Materials Page ABLE OF xi ONTENTS 1 About the TigerStack 10G . . . . . . . . . . . . . . . . . . . . . . 1-1 Page APPENDICES: Page xv ABLES Page F xvii IGURES Page Page TACK PowerSocket RedundantPower Socket ModuleSlot StackingPorts Up Down 50-60Hz2A Description of Hardware Page H 1-5 Status LEDs Figure 1-3 Port LEDs System Status LEDs T 10G 1-6 Figure 1-4 System LEDs H 1-7 Table 1-2 System Status LEDs Features and Benefits Page Page HAPTER 2-1 2 N P ETWORK LANNING Introduction to Switching Application Examples Collapsed Backbone Figure 2-1 Collapsed Backbone Servers 1Gbps Workstations 100Mbps E PPLICATION Console Module ... P ETWORK Console Module Console E PPLICATION Console Module VLAN1 Application Notes HAPTER 3-1 3 S THE NSTALLING Ethernet Cabling Equipment Checklist Mounting 3-5 S Select Master StackID 3-7 Installing an Optional SFP Transceiver into the Switch S 3-8 Connecting Switches in a Stack Page Connecting to a Power Source P C Connecting to the Console Port Page Page Page -P D Console Module ES4549 Fiber Optic SFP Devices F SFP D O 4-5 N Connectivity Rules 1000BASE-T Cable Requirements 1000 Mbps Gigabit Ethernet Collision Length R 4-7 100 Mbps Fast Ethernet Collision Domain 10 Mbps Ethernet Collision Domain Table 4-3 Maximum 1000BASE-LX Fiber Optic Cable Length Table 4-4 Maximum 1000BASE-ZX Fiber Optic Cable Length Cable Labeling and Connection Records A-1 ROUBLESHOOTING Diagnosing Switch Indicators Table A-1 Troubleshooting Chart A-2 Power and Cooling Problems Installation -B A A-3 In-Band Access Stack Troubleshooting Page B-1 B ABLES Twisted-Pair Cable and Pin Assignments B-2 10BASE-T/100BASE-TX Pin Assignments Straight-Through Wiring -P A IN P AND B-4 1000BASE-T Pin Assignments 1000BASE-T Cable Requirements Page Fiber Standards C-1 C S PECIFICATIONS Physical Characteristics C-2 F C-3 Switch Features Management Features Standards C-4 Compliances Warranty D-1 D O I RDERING NFORMATION Page G Glossary-1 LOSSARY Glossary-2 Glossary-3 Glossary-4 Glossary-5 Page NDEX Index-1 Numerics A B L M N O P T