SMC Networks 10G Fiber Optic SFP Devices

M

AKING

N

ETWORK

C

ONNECTIONS

4-4

Fiber Optic SFP Devices

An optional Gigabit SFP transceiver (1000BASE-SX, 1000BASE-LX or

1000BASE-ZX) can be used for a backbone connection between switches,

or for connecting to a high-speed server.

Each multimode fiber optic port requires 50/125 or 62.5/125 micron

multimode fiber optic cabling with an LC connector at both ends. Each

single-mode fiber port requires 9/125 micron single-mode fiber optic

cable with an LC connector at both ends.

Caution: This switch uses lasers to transmit signals over fiber optic

cable. The lasers are compliant with the requirements of a

Class 1 Laser Product and are inherently eye safe in normal

operation. However, you should never look directly at a

transmit port when it is powered on.

1. Remove and keep the LC port’s rubber cover. When not connected to

a fiber cable, the rubber cover should be replaced to protect the optics.

2. Check that the fiber terminators are clean. You can clean the cable

plugs by wiping them gently with a clean tissue or cotton ball

moistened with a little ethanol. Dirty fiber terminators on fiber cables

will impair the quality of the light transmitted through the cable and

lead to degraded performance on the port.

Contents

Main TigerStack 10G Gigabit Ethernet Switch Installation Guide Page Page Trademarks: L W IMITED ARRANTY ii iii OMPLIANCES Japan VCCI Class A FCC - Class A Industry Canada - Class A iv CE Mark Declaration of Conformance for EMI and Safety (EEC) v Taiwan BSMI Class A Australia AS/NZS 3548 (1995) - Class A Safety Compliance vi Power Cord Sa fety vii Veuillez lire fond l'information de la scurit suivante avant d'installer le Switch: viii Bitte unbedingt vor dem Einbauen des Switches die folgenden Sicherheitsanweisungen durchlesen: ix Warnings and Cautionary Messages Environmental Statement End of Product Life Span Manufacturing Materials Page ABLE OF xi ONTENTS 1 About the TigerStack 10G . . . . . . . . . . . . . . . . . . . . . . 1-1 Page APPENDICES: Page xv ABLES Page F xvii IGURES Page Page TACK PowerSocket RedundantPower Socket ModuleSlot StackingPorts Up Down 50-60Hz2A Description of Hardware Page H 1-5 Status LEDs Figure 1-3 Port LEDs System Status LEDs T 10G 1-6 Figure 1-4 System LEDs H 1-7 Table 1-2 System Status LEDs Features and Benefits Page Page HAPTER 2-1 2 N P ETWORK LANNING Introduction to Switching Application Examples Collapsed Backbone Figure 2-1 Collapsed Backbone Servers 1Gbps Workstations 100Mbps E PPLICATION Console Module ... P ETWORK Console Module Console E PPLICATION Console Module VLAN1 Application Notes HAPTER 3-1 3 S THE NSTALLING Ethernet Cabling Equipment Checklist Mounting 3-5 S Select Master StackID 3-7 Installing an Optional SFP Transceiver into the Switch S 3-8 Connecting Switches in a Stack Page Connecting to a Power Source P C Connecting to the Console Port Page Page Page -P D Console Module ES4549 Fiber Optic SFP Devices F SFP D O 4-5 N Connectivity Rules 1000BASE-T Cable Requirements 1000 Mbps Gigabit Ethernet Collision Length R 4-7 100 Mbps Fast Ethernet Collision Domain 10 Mbps Ethernet Collision Domain Table 4-3 Maximum 1000BASE-LX Fiber Optic Cable Length Table 4-4 Maximum 1000BASE-ZX Fiber Optic Cable Length Cable Labeling and Connection Records A-1 ROUBLESHOOTING Diagnosing Switch Indicators Table A-1 Troubleshooting Chart A-2 Power and Cooling Problems Installation -B A A-3 In-Band Access Stack Troubleshooting Page B-1 B ABLES Twisted-Pair Cable and Pin Assignments B-2 10BASE-T/100BASE-TX Pin Assignments Straight-Through Wiring -P A IN P AND B-4 1000BASE-T Pin Assignments 1000BASE-T Cable Requirements Page Fiber Standards C-1 C S PECIFICATIONS Physical Characteristics C-2 F C-3 Switch Features Management Features Standards C-4 Compliances Warranty D-1 D O I RDERING NFORMATION Page G Glossary-1 LOSSARY Glossary-2 Glossary-3 Glossary-4 Glossary-5 Page NDEX Index-1 Numerics A B L M N O P T